Bryant 558F.36.1 manual Notes For Fig, NOTES FOR , 4

NOTES FOR FIG. 1, 2, 5, 6, 9

1.If any of the original wire furnished must be replaced, it must be replaced with Type 90 C wire or its equivalent.

2.Three-phase motors are protected under primary single-phasing conditions.

3.Thermostat:

HH07AT170, 172, 174, and P272-2783 Subbase:

HH93AZ176, 178, and P272-1882, 1883

4.Set heat anticipator at 1 amp.

5.Use copper conductors only.

6.Use copper, copper-clad aluminum or aluminum conductors.

7.For 208/230-3-60 v units: TRAN is wired for 230-v unit. If unit is to be run with 208-v power supply, disconnect BLK wire from 230-v tap (RED) and connect to 208-v tap (BLU). Insulate end of 230-v tap.

NOTES FOR FIG. 3, 4, 7, 8, 10

1.	If any of the original wire furnished must be replaced, it must be	4.	Set heat anticipator at 1 amp.
	replaced with Type 90 C wire or its equivalent.	5.	Use copper conductors only.
2.	Three-phase motors are protected under primary single-phasing	6.	Use copper, copper-clad aluminum or aluminum conductors.
	conditions.

3.Thermostat:

HH07AT170, 172, 174, and P272-2783 Subbase:

HH93AZ176, 178, and P272-1882, 1883

NOTES FOR FIG. 11

1.If any of the original wire furnished must be replaced, it must be replaced with Type 90 C wire or its equivalent.

2.Three-phase motors are protected under primary single-phasing conditions.

3.Thermostat:

HH07AT170, 172, 174, and P272-2783 Subbase:

HH93AZ176, 178, and P272-1882, 1883

4.Set heat anticipator at 1 amp.

5.Use copper conductors only.

6.Use copper, copper-clad aluminum or aluminum conductors.

7.For 208/230-3-60 v units: TRAN is wired for 230-v unit. If unit is to be run with 208-v power supply, disconnect BLK wire from 230-v tap (RED) and connect to 208-v tap (BLU). Insulate end of 230-v tap.

8.

CIRCUIT				MUST
	VOLTS	MFG. PT. NO.		TRIP
BREAKER
				AMPS
CB	24 V	Potter & Brumfield
		W2BX-1024-3.2		3.2
CB1 150	460-3-60	Heinemann	Airpax
		CF3-Z228-4	219-3-2600-486	8.5

NOTES FOR FIG. 12

1. If any of the original wire furnished must be replaced, it must be	7.
replaced with Type 90 C wire or its equivalent.

2.Three-phase motors are protected under primary single-phasing conditions.

3.Thermostat:

HH07AT170, 172, 174, and P272-2783 Subbase:

HH93AZ176, 178, and P272-1882, 1883

4.Set heat anticipator at 1 amp.

5.Use copper conductors only.

6.Use copper, copper-clad aluminum or aluminum conductors.

CIRCUIT				MUST
	VOLTS	MFG. PT. NO.		TRIP
BREAKER
				AMPS
CB	24 V	Potter & Brumfield
		W2BX-1024-3.2		3.2
CB1 150	460-3-60	Heinemann	Airpax
		CF3-Z228-4	219-3-2600-486	8.5

—2—