6B/9B AMPLIFIER BRIDGED MODE HOOKUP
11
To SOURCE SIGNAL
While balanced inputs are used here, bridging can also be accomplished using the single ended inputs as shown at right.
The same signal is fed into both amplifier channel inputs via a “Y” adaptor cable. Note that the POLARITY of one channel is the inverse of the other. THIS IS ESSENTIAL for the amplifier to operate in bridged mode. Failure to INVERT one of the channels relative to the other will result in zero output. It does not matter which channel is set to zero degrees and which one is set to 180 degrees, however, as long as they are different.
When bridging two channels together the resultant output will be increased by 6 dB relative to the output of a single channel. To keep the gain of a bridged channel the same as that of a single channel, the SENSITIVITY switch should be set to a higher voltage setting. For example, if a single channel is set to “1V” sensitivity, then both the bridged channels would be set to “2V”. Likewise, if a single channel were set to a sensitivity of “2V”, then the bridged channels would be set to “4V”.
When bridging “PRO” channels which are |
| |
equipped with level controls, it is |
| |
imperative that the level controls on BOTH | While single ended or unbalanced inputs are used here, | |
channels being bridged be set to their | ||
bridging can also be accomplished using the balanced inputs | ||
maximum | ||
as shown to the left. | ||
|
9BSST FIVE CHANNEL POWER AMPLIFIER
|
|
| PUSH |
|
|
XLR/PHONE INPUT |
|
| HOME THEATRE SETTINGS | ||
Pin 1/SLEEVE: | GND |
|
| BALANCED INPUT: | 2V |
Pin 2/TIP: | POS(+) |
|
| SINGLE ENDED INPUT: | 1V |
Pin 3/RING: |
|
| See manual for further details. | ||
| POLARITY | BALANCED | SENSITIVITY |
| |
| 0 |
| INPUT | for 100W @ 8 |
|
|
|
|
|
| |
|
|
|
| 4v |
|
|
|
|
| 2v |
|
|
|
|
| 1v |
|
| 180 | SINGLE ENDED |
| ||
|
|
| INPUT |
|
|
|
|
| OUTPUT |
|
|
|
|
| 250W/8 |
|
|
WARNING! RISK OF HAZARDOUS ENERGY. MAKE PROPER SPEAKER CONNECTIONS. |
| ||||
| SEE OPERATING MANUAL BEFORE USING. |
|
|
|
| PUSH |
|
|
XLR/PHONE INPUT |
|
| HOME THEATRE SETTINGS | ||
Pin 1/SLEEVE: | GND |
|
| BALANCED INPUT: | 2V |
Pin 2/TIP: | POS(+) |
|
| SINGLE ENDED INPUT: | 1V |
Pin 3/RING: |
|
| See manual for further details. | ||
| POLARITY | BALANCED | SENSITIVITY |
| |
| 0 |
| INPUT | for 100W @ 8 |
|
|
|
|
|
| |
|
|
|
| 4v |
|
|
|
|
| 2v |
|
|
|
|
| 1v |
|
| 180 | SINGLE ENDED |
| ||
|
|
| INPUT |
|
|
|
|
| OUTPUT |
|
|
|
|
| 250W/8 |
|
|
WARNING! RISK OF HAZARDOUS ENERGY. MAKE PROPER SPEAKER CONNECTIONS. |
| ||||
| SEE OPERATING MANUAL BEFORE USING. |
|
|
|
| PUSH |
|
|
XLR/PHONE INPUT |
|
| HOME THEATRE SETTINGS | ||
Pin 1/SLEEVE: | GND |
|
| BALANCED INPUT: | 2V |
Pin 2/TIP: | POS(+) |
|
| SINGLE ENDED INPUT: | 1V |
Pin 3/RING: |
|
| See manual for further details. | ||
| POLARITY | BALANCED | SENSITIVITY |
| |
| 0 |
| INPUT | for 100W @ 8 |
|
|
|
|
|
| |
|
|
|
| 4v |
|
|
|
|
| 2v |
|
|
|
|
| 1v |
|
| 180 | SINGLE ENDED |
| ||
|
|
| INPUT |
|
|
|
|
| OUTPUT |
|
|
|
|
| 250W/8 |
|
|
WARNING! RISK OF HAZARDOUS ENERGY. MAKE PROPER SPEAKER CONNECTIONS. |
| ||||
| SEE OPERATING MANUAL BEFORE USING. |
|
|
|
| PUSH |
|
|
XLR/PHONE INPUT |
|
| HOME THEATRE SETTINGS | ||
Pin 1/SLEEVE: | GND |
|
| BALANCED INPUT: | 2V |
Pin 2/TIP: | POS(+) |
|
| SINGLE ENDED INPUT: | 1V |
Pin 3/RING: |
|
| See manual for further details. | ||
| POLARITY | BALANCED | SENSITIVITY |
| |
| 0 |
| INPUT | for 100W @ 8 |
|
|
|
|
|
| |
|
|
|
| 4v |
|
|
|
|
| 2v |
|
|
|
|
| 1v |
|
| 180 | SINGLE ENDED |
| ||
|
|
| INPUT |
| To |
|
|
|
|
| |
|
|
|
|
| SOURCE |
|
|
|
|
| SIGNAL |
|
|
| OUTPUT |
|
|
|
|
| 250W/8 |
|
|
WARNING! RISK OF HAZARDOUS ENERGY. MAKE PROPER SPEAKER CONNECTIONS. |
| ||||
| SEE OPERATING MANUAL BEFORE USING. |
|
HEAT
When two 6B channels are bridged the power output can exceed 800 Watts. Two 9B channels can provide over 300 Watts. When operated at these elevated power levels there is a p o s s i b i l i t y o f t h e a m p l i f i e r overheating. When overheated they will automatically be shutdown by internal protection circuitry to prevent any damage occurring to the amplifier. To prevent overheating it may be necessary to provide external fan cooling especially if the amplifier is installed in an enclosed cabinet and operated at or near maximum power levels.
ALTHOUGH 6B CHANNELS ARE SHOWN, THE
SAME HOOKUP APPLIES TO 9B CHANNELS
While any two channels can be bridged, we recommend that adjacent channels be used (as shown) to facilitate the external wiring between the channels. Note that only the POSITIVE (+) terminals on the 6B power amplifier modules are connected to the speaker. A ground wire (16g or heavier wire recommended) must be connected between the two BLACK output terminals on the 6B amplifier channels being bridged. DO NOT CONNECT ANYTHING ELSE TO EITHER OF THESE BLACK OUTPUT TERMINALS!
The red (positive) output terminal of the
BRIDGING KITS
Bryston can supply Bridging Kits consisting of a “Y” adaptor cable and a ground strap cable. The “Y” adaptor cable can be equipped with either RCA (Phono) connectors (Part # 150901) for