ELECTRICAL REQUIREMENTS

WARNING - The brewer must be disconnected from the power source until specified in Initial Set-Up.

Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.

L2 RED

L1 BLACK

GREEN

L2 RED

L2

L1 BLACK

L1

GREEN G

L2 RED

L2 RED

L2

 

 

WHITE

WHITE

N

NEUTRAL

NEUTRAL

 

L1 BLACK

L1 BLACK

L1

 

 

 

GREEN

 

 

 

 

 

 

GREEN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

200 and 230 volt ac models

120/208 and 120/240 volt ac models

Note: This electrical service consists of 2 current carrying conductors (L1 and L2) and a separate conductor for earth ground.

Note: This electrical service consists of 3 cur- rent carrying conductors (Neutral, L1 and L2) and a separate conductor for earth ground.

ELECTRICAL HOOK-UP (Models without power cord)

CAUTION – Improper electrical installation will damage electronic components. Damage caused by incorrect electrical connections is not covered by warranty.

1.An electrician must provide electrical service as specified in conformance with all local, state and federal electrical codes.

2.Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

3.Remove the front panel beneath the sprayheads to gain access to the terminal block.

4.Feed the cord through the strain relief and connect it to the terminal block.

5.Connect the brewer to the power source and verify the voltage at the terminal block before proceeding. Re- place the front panel.

6.If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing has been hooked up, the brewer is ready for Initial Set-Up.

ELECTRICAL HOOK-UP (Models with power cord)

WARNING – If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personel with a special cord available from the manufacturer or its authorized service personel in order to avoid a hazard. Improper electrical installation will damage electronic components. Damage caused by incorrect electrical connections is not covered by warranty.

1.An electrician must provide electrical service as specified in conformance with all local, state and federal electrical codes.

2.Using a voltmeter, check the voltage and color coding of each conductor at the electrical source. NOTE - If the brewer was shipped without a plug on the power cord a qualified service personnel must select and install the proper UL listed grounding type attachment plug specified on the rear of the brewer.

3.Remove the front panel beneath the sprayheads to gain access to the terminal block.

4.Connect the brewer to the power source and verify the voltage at the terminal block before proceeding.

5.If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumb- ing has been hooked up, the brewer is ready for Initial Set-Up.

WARNING – Electrical connections must be made as specified above. Failure to follow these instructions can

result in personal injury, property or equipment damage.

Page 4

29877.4 031312

 

Page 3 Page 5
Page 4
Image 4
Bunn DUAL068000 manual Electrical Requirements, Electrical HOOK-UP Models without power cord
Page 3 Page 5

DUAL068000 specifications

The Bunn DUAL068000 is an advanced commercial coffee maker designed for high-volume environments where speed, efficiency, and quality are paramount. This dual-brew coffee maker seamlessly combines performance with innovative technologies to meet the demands of cafes, restaurants, and convenience stores.

One of the standout features of the DUAL068000 is its dual brewing capabilities. It allows for the simultaneous brewing of two different types of coffee. This flexibility is particularly valuable in busy settings where diverse customer preferences must be accommodated. Operators can brew a full pot of drip coffee while simultaneously preparing a specialty coffee drink, optimizing workflow and minimizing wait times.

Equipped with a powerful heating element, this coffee maker can brew a full 12-cup pot in under four minutes. This rapid brewing time ensures that fresh coffee is always available, keeping customers satisfied and coming back for more. The DUAL068000 utilizes a unique hot water faucet that provides water on demand, making it easy to prepare tea or other hot beverages without disruption to the brewing process.

The DUAL068000 incorporates Bunn’s patented brewing technology, which includes temperature control and precision brewing features. The machine maintains consistency in water temperature throughout the brewing cycle, ensuring optimal extraction and rich flavor profiles in every cup. Its adjustable brew time allows operators to customize the strength of their coffee according to specific needs.

In terms of durability, the Bunn DUAL068000 is built to withstand the rigors of commercial use. Made from high-quality stainless steel, it offers a robust design that is both easy to clean and resistant to wear and tear over time. The easy-to-navigate control panel provides intuitive operation, allowing staff to quickly adjust settings without extensive training.

Another key characteristic of this machine is its energy-efficient design. Bunn has incorporated features that minimize energy consumption while maximizing output, making the DUAL068000 an eco-friendly choice for coffee businesses seeking to reduce their carbon footprint.

Overall, the Bunn DUAL068000 coffee maker combines reliability, efficiency, and flexibility, making it an ideal choice for any establishment looking to serve exceptional coffee quickly and efficiently. Its advanced technology and robust build quality position it as a leader in the commercial coffee maker market.
Top Page Image Contents