TEMPERATURE SELECTION (cont)

SET READY - Range: 185˚F (85˚C) to 203˚F (95˚C)

This function allows the operator to set the minimum temperature allowable to start a brew cycle. The range

can be from 185˚F (85˚C) to within 2˚F (-1.7°C) of the SET TEMP. The water must be at the SET READY tempera-

ture or higher for the display to indicate READY TO BREW. If brew lockout is enabled, the brewing process will not start below this READY temperature.

NOTE: The upper limit for SET READY temperature is 2˚F (-1.7°C) less than the water temperature (SET TEMP)

setting.

SET READY: XXX° (-) DONE (+)

Procedure to set ready temperature:

1.Press and hold upper right hidden switch until the display reads SELECT RECIPE. Release switch. Continue to press and release switch until the display reads SET READY.

2.To adjust the ready temperature, press the (-)button to decrease, or (+) to increase the ready temperature.

3.When finished, press and release DONE to save the new setting, exit the SET READY function and advance to the next function screen, REFILL. Another alternative is to press and release the ON/OFF switch (either on DUAL brewers) located on the front switch panel to exit the SET READY function and return to the MAIN

SCREEN.

COFFEE BREWING

1.Insert a BUNN filter into the Smart Funnel.

2.If a grinder is not used to obtain the coffee grounds, pour the proper amount of fresh coffee grounds into the funnel and level by gently shaking. Slide the funnel into the funnel rails and select batch size. Proceed to step 5.

3.If a G9-2T DBC or MHG grinder is used with a compatible Smart Funnel, select the desired batch size on the grinder. Grind the selected amount of fresh coffee into funnel and level grounds by gently shaking. It is not necessary to select a size on the brewer.

4.Slide the funnel into the funnel rails. The brewer will read the size ground through the chip in the funnel handle and will automatically select the correct size to brew.

5.Place an empty server under the funnel.

6.The ENABLE BREW switch must be ON. Momentarily press and release the "BREW" switch. If the brewer has the funnel lock option and if it is activated, once a brew cycle has been started the funnel is locked in place. There may be certain situations in which the brew cycle will not begin when the brew switch is pressed:

a)BREW TEMPERATURE TOO LOW - wait until heated or cancel BREW LOCKOUT option.

b)FUNNEL NOT IN PLACE (or using a standard brew funnel) - cancel FUNNEL DETECT option.

c)CHECK FUNNEL - remove funnel, empty previously brewed grounds and grind a new batch into funnel.

d)SERVER NOT IN PLACE - place Soft Heat Server, or cancel SERVER DETECT option.

7.If none of the above messages are displayed, the display will read NOW BREWING and the time remaining in the brew cycle. Arrows will point to the side which is brewing. If both sides are brewing simultaneously, the arrows will alternate from left to right on the display.

8.Following the BREW will be a countdown of DRIPPING time which shows the time remaining until the funnel lock will release. Discard the grounds and filter only after visible dripping stops.

Page 8

29877.4 031312

 

Page 7 Page 9
Page 8
Image 8
Bunn DUAL068000 manual Coffee Brewing, SET Ready Range 185˚F 85˚C to 203˚F 95˚C, Procedure to set ready temperature
Page 7 Page 9

DUAL068000 specifications

The Bunn DUAL068000 is an advanced commercial coffee maker designed for high-volume environments where speed, efficiency, and quality are paramount. This dual-brew coffee maker seamlessly combines performance with innovative technologies to meet the demands of cafes, restaurants, and convenience stores.

One of the standout features of the DUAL068000 is its dual brewing capabilities. It allows for the simultaneous brewing of two different types of coffee. This flexibility is particularly valuable in busy settings where diverse customer preferences must be accommodated. Operators can brew a full pot of drip coffee while simultaneously preparing a specialty coffee drink, optimizing workflow and minimizing wait times.

Equipped with a powerful heating element, this coffee maker can brew a full 12-cup pot in under four minutes. This rapid brewing time ensures that fresh coffee is always available, keeping customers satisfied and coming back for more. The DUAL068000 utilizes a unique hot water faucet that provides water on demand, making it easy to prepare tea or other hot beverages without disruption to the brewing process.

The DUAL068000 incorporates Bunn’s patented brewing technology, which includes temperature control and precision brewing features. The machine maintains consistency in water temperature throughout the brewing cycle, ensuring optimal extraction and rich flavor profiles in every cup. Its adjustable brew time allows operators to customize the strength of their coffee according to specific needs.

In terms of durability, the Bunn DUAL068000 is built to withstand the rigors of commercial use. Made from high-quality stainless steel, it offers a robust design that is both easy to clean and resistant to wear and tear over time. The easy-to-navigate control panel provides intuitive operation, allowing staff to quickly adjust settings without extensive training.

Another key characteristic of this machine is its energy-efficient design. Bunn has incorporated features that minimize energy consumption while maximizing output, making the DUAL068000 an eco-friendly choice for coffee businesses seeking to reduce their carbon footprint.

Overall, the Bunn DUAL068000 coffee maker combines reliability, efficiency, and flexibility, making it an ideal choice for any establishment looking to serve exceptional coffee quickly and efficiently. Its advanced technology and robust build quality position it as a leader in the commercial coffee maker market.
Top Page Image Contents