F. Route control chain to convenient location and fasten to tractor. Be sure excess slack is removed from the chain to avoid entanglement with tractor tires or other moving parts. Make sure latch locking pins are in the stored positions so that latches can

Figure 2-3

Control Chain

be released by pulling the chain.(Refer to Figures 3-3 and 3-4)

G. Attach driveline to tractor . Pull on each drive- line section to be sure that yoke locks into place.

H. Securely attach safety tow chain to tractor.

SECTION III

OPERATING INSTRUCTIONS

3-1 GENERAL SAFETY

Only qualified people familiar with this operator’s manual and tractor operator’s manual should oper- ate this machine. Operator should wear hard hat, safety glasses and safety shoes. The operator should read, understand and practice all safety mes- sages shown on the caution, warning and danger decals affixed to the mower to avoid serious injury or death. It is recommended that tractor be equipped with Rollover Protective System (ROPS) and a seat belt be used. Before beginning operation, clear work area of any objects that may be picked up and thrown. Check for ditches, stumps, holes or other obstacles that could upset tractor or damage mower. Always lower mower to ground and allow blades to come to a complete stop, set parking brake and turn off tractor engine before leaving tractor operator’s seat.

NOTE: Before initial operation the TDR should be con- nected to the tractor for a 30 minute “run in” cycle. During the “run in” phase, the tractor should be operated at only half throttle. The “run in” phase will allow belt warm-up and stretching before initial operation. After the 30 minute “run in” cycle is complete, ALL belts should be inspected for proper tension and if adjustments are necessary, refer to Maintenance Section.

3-2 CUTTING HEIGHT ADJUSTMENT

The mower should be operated at the highest posi- tion that will give desired cutting results. This will help prevent blades from striking the ground, reduc- ing blade wear and undue strain on the machine. Cutting too much material may leave excess clip- pings on the surface. The more frequently the grass

is mowed, the better the effect will be.

A. Raise mower off ground enough to remove caster.

WARNING

THE MOWER CAN FALL FROM HYDRAULIC SYSTEM FAILURE. TO AVOID SERIOUS INJURY OR DEATH, SECURELY SUPPORT MOWER BEFORE WORKING UNDERNEATH.

B. Remove pin securing caster stem to caster arm. Remove caster stem from caster arm.

C. Place amount of spacers on caster stem to give desired cutting height. With no spacers on the bottom, a 3/4” cutting height is given. (Figure 3-1)

D. Reinstall caster stem into caster arm. Place remaining spacers on caster stem above caster arm and install pin to retain.

E. Repeat operation for all caster wheels. Make certain all wheels are adjusted to the same height.

Figure 3-1

Caster Wheel

Spacers

9

Page 10 Page 12
Page 11
Image 11
Bush Hog TDR-11 manual Section Operating Instructions, General Safety, Cutting Height Adjustment
Page 10 Page 12

TDR-11 specifications

The Bush Hog TDR-11 is a powerful and versatile implement designed for agricultural and landscaping applications. This robust rotary cutter is engineered to handle a range of demanding tasks, making it an essential tool for farmers, property owners, and landscapers alike. The TDR-11 is primarily known for its efficient cutting capabilities and durability, which are paramount for maintaining fields, pastures, and overgrown areas.

One of the standout features of the Bush Hog TDR-11 is its cutting width of 11 feet, allowing operators to cover large areas in a single pass. This efficiency significantly reduces the time required to clear land or manage vegetation, making it ideal for those with extensive properties. The cutter is designed to handle tough materials, including dense brush and heavy grasses, thanks to its impressive cutting performance.

In terms of construction, the TDR-11 boasts a heavy-duty design. The frame is built from high-strength steel, ensuring durability and long-lasting performance even under the most challenging conditions. The reinforced deck contributes to its ability to resist wear and tear, providing reliability throughout the years.

Another key characteristic of the Bush Hog TDR-11 is its Triple Blade design. These blades are crafted to provide a clean and even cut while minimizing debris and mess. The adjustable blade height empowers the operator to adapt the cutting height to their specific requirements, ensuring optimal results for various applications.

The TDR-11 features a slip clutch driveline, a technology that protects the machine from shock loads and enhances its longevity. This feature allows the implement to operate smoothly while preventing potential damage from unexpected obstacles encountered during operation.

Moreover, the Bush Hog TDR-11 is designed for easy attachment and detachment, making it user-friendly and efficient for operators who may need to switch between different implements frequently. The universal mounting system ensures compatibility with a wide range of tractors, enhancing versatility.

Overall, the Bush Hog TDR-11 is a testament to engineering excellence in rotary cutters, combining robust construction, advanced technology, and practical features. Its capacity to handle various cutting tasks while maintaining ease of use solidifies its position as a reliable choice for those in need of an efficient land management solution. Whether for agricultural purposes or landscaping, the TDR-11 proves to be a valuable asset, delivering performance that meets and exceeds expectations.
Top Page Image Contents