GENERAL SAFETY RULES
READ AND FULLY UNDERSTAND ALL
INSTRUCTIONS AND WARNINGS PRIOR TO
USING THIS SAW. YOUR SAFETY IS MOST
IMPORTANT! FAILURE TO COMPLY WITH WARNING! PROCEDURES AND SAFE GUARDS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE. REMEMBER: YOUR PERSONAL
SAFETY IS YOUR RESPONSIBILITY!
12.Place the nock/insert end of the arrow shaft into the notch in the Shaft Position Bracket. Figure 8
13.Gently guide the end of the arrow shaft to be cut into the Cutting Blade until it is completely cut. Figure 8
14.Carefully remove the cut arrow shaft from the Arrow Shaft Guide and Shaft Position Bracket. Be careful to not allow the arrow shaft to further contact the Cutting Blade.
15.Turn the Arrow Saw to the ‘OFF’ Position. Turn off the attached vaccuum.
DisconnectCutti g Bladefrom the power source when not in use. | Shaft Position | FIGURE 8 |
1. | Check for damaged parts. BEFORE | ||
using the | Arrow Saw, check that all parts | ||
are operating properly and perform their | |||
intended functions. Check for alignment | |||
of moving parts, binding of moving parts, | |||
and any other condition that may affect the | |||
Arrow Saw operation. |
| ||
2. | ALWAYS DISCONNECT | Arrow | |
Saw from power source before servicing, | |||
changing accessories or cleaning the unit. | |||
3. | To Reduce risk of unintentional starting, | ||
make sure the power switch is in the | “OFF” | ||
position before connecting the Arrow Saw | |||
to the power source. |
| ||
4. | DO NOT IMMERSE THE ARROW | ||
SAW INTO WATER OR OTHER LIQUID, | |||
OR OPERATE NEAR A WATER SOURCE. | |||
SERIOUS | INJURY FROM ELECTRIC | ||
10. | DO NOT operate the Arrow Saw if |
it is damaged or malfunctions in any way. | |
Instead, please call Customer Service. | |
11. | Tie back loose hair and clothing, roll |
up long sleeves, and remove ties and rings, | |
bracelets and other jewelry before operating | |
the | Arrow Saw. |
12. | DO NOT use the Arrow Saw if the |
power cord is frayed or damaged in any | |
way. | |
13. | Keep the power cord well clear of the |
Arrow Saw blade during operation. | |
14. | DO NOT operate Arrow Saw while |
under the influence of drugs or alcohol. | |
15. | The Arrow Saw is for household use |
only. Commercial use of the Arrow Saw will | |
Arrow Shaft | Bracket |
Arrow Shaft | CAUTION ROTATING SHARP BLADE! |
Guide | To avoid severe injury keep fingers, hands and other foreign |
| objects clear of the saw opening Blade and Moving Parts of the |
| Arrow Saw. Wear approved Safety Glasses and Kevlar Gloves |
| when using the Arrow Saw. |
ROLL CUTS
WARNING! Before cleaning, assembling or disassembling the Arrow Saw, make sure it is turned OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!
SHOCK COULD RESULT. | |
5. | DO NOT operate the Arrow Saw with |
wet hands or bare feet. | |
6. | The Arrow Saw is not a toy. KEEP |
CHILDRENAWAYfrom the unit at ALL times. | |
NEVER LEAVE THE UNIT UNATTENDED | |
DURING OPERATION. | |
7. | Keep fingers clear of the Cutting Blade |
at all times. NEVER reach into the Arrow | |
Saw with fingers or other objects. Doing | |
so may result in personal injury or unit | |
damage. | |
void the warranty. | |
16. | Only operate the Arrow Saw on a flat, |
stable work surface. | |
17. | NEVER install any accessories or parts |
from other manufacturers on the Arrow | |
Saw. Doing so may damage the unit and | |
will void the warranty. | |
18. | ALWAYS make sure the Cutting |
Blade is properly secured before operating | |
the Arrow Saw. Always stand clear of the | |
Cutting Blade during start up. | |
19. | ALWAYS clean the area near the |
1.Set the On/Off Power Switch to the “OFF” position. Disconnect the
Power Cord from the power source.
2.Loosen the two Thumb Screws holding the Blade Shield to the Arrow Saw. Figure 9
3.Remove the Thumb Screws and Blade Shield.
4.Using an Allen Wrench, loosen, but do not remove, the Socket Head Cap Screw securing the Arrow Shaft Guide to the Base. Figure 10
Blade Shield | FIGURE 9 |
Arrow Shaft | Thumb Screws |
| |
Guide |
|
8. | Any improper use or modification of |
the | Arrow Saw will void the warranty. |
9. | DO NOT attempt electrical repairs. Any |
electricalrepairmustbedonebyanauthorized | |
service technician. If your Arrow Saw | |
needs repairing, contact Customer Service. | |
Cutting Blade. Keep it clear of dust and |
debris to prevent damaging the blade. |
20. Wear eye protection at all times |
while the Arrow Saw is in use. Everyday |
eye glasses are not safety glasses. Safety |
glasses confirm to ANSI Z87.z requirements. |
Approved safety glasses have Z87 printed |
or stamped on them. |
5. Adjust the Arrow Shaft Guide until the Cutting | |
Blade extends about halfway through the arrow | |
shaft. Figure 7 | |
6. | Firmly tighten the Socket Head Cap Screw |
to secure the Arrow Shaft Guide to the Base. | |
7. | Replace the Blade Shield. CAUTION: |
Halfway through the arrow shaft
FIGURE 10
Cutting
Blade
Base
SAVE THESE INSTRUCTIONS!
Refer to them to instruct others.
NEVER OPERATE THE ARROW SAW |
WITHOUT THE BLADE SHIELD SECURELY |
MOUNTED IN PLACE! |
Arrow Shaft
Guide
Socket Head
Cap Screw
