Cadence T1 manual Time Mode, Chrono Mode

Thank you for purchasing a Cadence T1 Watch from NK.The Cadence is the complete rower’s timepiece; it is a full-functioning digital watch, as well as a wireless rate meter. The patented tilt- switch technology calculates stroke rate based on the feathering interval. There are no wires to install, making the Cadence an ideal tool for rowers who use different boats. Coaches and spectators can press the large rate button to take stroke rates at any time.It’s even possible to measure rates with one hand by simulating the feathering motion with the watch hand - great when driving a motorboat.

Button Functions:	Press the MODE button to
	cycle through the modes:

To recall the data (the chronograph must be stopped):

1. Hold the Recall	“HOLDTO RECALL” will be displayed ,with a beep when entering Recall
button for 3 seconds.	Mode.
2. Press the + button	The date and time when the chronograph was started will be displayed.
to cycle through the	After reviewing all splits, the Best Lap screen and Avgerage screen will
lap times.	display the shortest and average of all stored laps.
3. Press the - button
to cycle through the
times in reverse
order.
4. Press the Mode
button to exit Recall.

Illuminate

Backlight

Start & Stop

Chronograph

Take Manual Rate(s),

Advance to Next Setting

Take Splits,

Cycle Modes, Reset Chronograph

Set Clock/Alarm,

Recall Chronograph

TIME

CHRONO

RATE/TIME

RATE/CHRONO

ALARM

5. Hold the Reset	“HOLD TO CLEAR” and the chrono icon will be displayed. The watch will
button for 3 seconds	beep once and clear the data and return the chronograph to 00:00.0.
to clear the data.
6. Press the Mode	If the Chrono mode is exited without clearing the data, the memory
button to exit	will remain intact. If the Chrono mode is re-entered, the display will
Chrono Mode.	show the chronograph stopped on the last stored time. If the Mode
	button is pressed while the chronograph is running, the timer will
	continute to run even though it will not be displayed.

**If the lap time on the chronograph reaches 59:59.59 (HH:MM:SS),a“01” will appear just below the lap number,indicating the time is 1 hour.The Lap time will roll back to 00:00.00 and count up.

**The Manual Rate button will remain active in Chrono Mode, meaning rates can be measured at any time while the chronograph is running. If the Manual Rate button is pressed twice within 10 seconds, the rate will be displayed instead of the lap. After 10 seconds of no Rate button presses, the watch will return to regular Chrono mode. The Split and Start/Stop buttons will work the same. The internal tilt switch will not measure a stroke rate in this mode.

TIME MODE

Illuminate	Increase	Indicates
Backlight			Indicates
	Setting	if alarm
		is set	AM or PM
	Advance to		Time of
	Next Setting		Day
	Decrease	Day of	Date
Enter & Exit	Setting
Mode		the week

To set the clock and calendar:

1.Holdthe Setbutton	“HOLD TO SET” will be displayed, with a beep when entering the Time
for 3 seconds to set.	Setting Mode. The first setting (hours) will blink, indicating that the
	value may be changed.
2. Press the + button	Hold the + or - to increase or decrease the value quickly.
to increase or - to
decrease.
3. Press the >> button	Settings:Hour,minutes,seconds,year,month,date,12-hour or 24-hour
to advance to the	format,date format (MM-DD or DD-MM),and hourly chime (on or off).
next setting.
4. Repeat until all	Press the Mode button at any time to exit Date/Time setting. If no
values are set. Watch	buttons are pressed for 60 seconds, the watch will return to Date &
will return to Date &	Time mode.
Time mode when all
values are set.

CHRONO MODE

Illuminate		Start/Stop	Indicates		Indicates
Backlight		Chronograph	Chrono
			Mode		Lap Number
	LAP	Stroke	Lap	LAP	Hour
					indicator
		Rate	Time
Enter &		Splits			Cumulative
Exit Mode					Time
To run the chronograph:
1. Press the Mode
button to enter
Chrono Mode.
2. Press the Start		The chrono icon will blink when the timer is running. The lap time and
button to start the		cumulative time will begin counting from 00:00.0. The lap counter will
chronograph.		show 00.
3. Press the Split		The stored lap and cumulative time will freeze on the display for 8
button to store a lap.		seconds, then resume. The lap counter will increase by 1, up to 99 laps.
4. Press the Stop		The chrono icon will stop blinking and the lap and cumulative times will
button to stop the		freezeonthedisplay.IftheStartbuttonispressedagain,thechronograph
chronograph.		will resume timing without creating a lap.

RATE MODES (Rate/Time and Rate/Chrono)

The Cadence T1 measures stroke rates with an internal tilt switch that calculates the rate from feathering and squaring the blade. The tilt switch can also be used on the wrist by tilting it in unison with the feathering and squaring of an oar. It also measures rates when the Rate/Next button is pressed in conjunction with a crew’s catches.The watch updates the stroke rate once per stroke, and can measure 6-240 strokes per minute.

			Rate/Time Mode	Rate/ChronoMode
Illuminate		Start/Stop	Indicates AM or PM	Chronograph
				icon		Indicates Lap
Backlight		Chronograph	Stroke	Stroke
			Rate	Rate			LAP
	LAP	Stroke
		Rate
Enter &		Splits	Time
					Cumulative
Exit Mode			of Day	Chronograph Time
To measure stroke rates:
1. Press the	Mode
button to enter either
Stroke Rate mode.
2. Measure the rate		When the stroke rate is triggered for the first time, the display will
with either	Rate	show a 0 for the stroke rate. When triggered again within 10 seconds,
button or tilt switch.		the stroke rate will be calculated and displayed.

To use the chronograph while measuring rates:

1.Press the Mode button to enter the Rate/Chrono mode.

2.Press the Start The chrono icon will blink when the timer is running. When the lap

button to start the	button is pressed, the stored lap and cumulative time will freeze on
chronograph, and Split	the display for 8 seconds, then resume.
to store laps.
3. Press the Stop	The Cadence will continue to measure the stroke rate with either the
button to stop the	tilt switch or the rate button with the chronograph stopped. The
chronograph.	chronograph may be restarted at any time.

To recall the stored laps:

1. With chronograph	“HOLDTO RECALL” will be displayed,with a beep when entering Recall
stopped, hold the	Mode.
Recall button for 3
seconds.
2. ( The Recall will	Both lap and cumulative times will be displayed, even though only the
function the same as in	cumulative times were shown when the Rate/Chrono mode was
Chrono mode.)	timing.
3. Press the Mode
button to exit Recall.
4. Hold the Reset	“HOLD TO CLEAR” will be displayed, with a beep when clearing the
button for 3 seconds	chronograph. The display will return to Rate/Chrono mode.
to clear the data.