Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E manual Control Operation Adjustment, Program Mode, Security Access/Lockout

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 41

Program Mode

Program Mode

Use the Program Mode to customize the control to suit a variety of applications by programming the operating parameters. From the Stop Mode press the PROG key to access the Level 1 Program Mode. Hold the SHIFT key and press the PROG key to access the Level 2 Program Mode. When in the Program Mode press the SHIFT key then the UP/DOWN Arrow keys to change a parameter value. Pressing the ENTER key will save the new parameter value. To return to the Stop Mode, press the PROG key. Parameters may only be programmed when accessed from the Stop Mode. If entering the Programming Mode from the Run Mode the parameter values may only be viewed.

Security Access/Lockout

Access to the control parameters can be protected by use of the security code. Security is enabled, and the Security Code is defined by setting parameter 87-Security Access Code. If the Security Access Code is enabled and the Programming Mode is entered then the following display is shown to prompt for the previously defined Security Code. After the proper Security Code is entered, the display will return to the normal Programming Mode Display.

Control Operation Adjustment

The following control adjustments are available within the Series 10 inverter to allow custom tailoring of the drive for particular applications. Table NO TAG user parameters lists the location and possible values of the various control adjustments. The following paragraphs discuss control parameter adjustments and their effect on drive performance.

3-6 Operation

Image 41

Baldor ID101F50-E manual Control Operation Adjustment, Program Mode, Security Access/Lockout

Contents

MN710 6/98Series Inverter Control Installation and Operating Manual AC INVERTERSection Table of ContentsTable of Contents SectionMOL Terminal Connections Section16-Load Torque iv Table of Contents Appendix ASection SectionSection General Information Limited WarrantySafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Linear to Squared Reduced in 6 patterns Specifications0C to 40C Maximum without derating Keypad, 2 Wire, 3 Wire, Preset SpeedsOperator Keypad Fault ConditionsAnalog Outputs Relay OutputsRatings 1-8 General Information Location and Mounting Section Installation2-2 Installation Terminal Access Cover RemovalFigure 2-2 Terminal and Jumper Locations Wiring ConsiderationsTerminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Output Wire Size and Protection DevicesWire nameplate. Use of control with wrong power Main Circuit WiringRecommended Terminal Tightening Torques Do not use this control with any inputAC Power Connections 2-8 Installation Motor ConnectionsFigure 2-3 Typical Connections for M-Contactor M-ContactorAnalog Command Inputs Logic WiringExternal Trip Connection Analog OutputOpto Isolated Inputs Jumper J19 Selections Jumper J19 Input SelectionReference Selection Of Operation Mode And Connection DiagramsRelay Outputs Function 2 Wire Run/Stop ConnectionsSpeed Select Speed Select Ramp SelectFunction FunctionFunction 3 Wire Run/Stop ConnectionsSpeed Select 3 Wire Run/Stop, Electronic Potentiometer Connections 2 Wire Run/Stop, Electronic Potentiometer ConnectionsSee recommended tightening torques for terminal connectors Parameter 21 - Operating Mode =Analog Meter MOL Terminal Connections 77-External Trip SelectRelay Output Pull±Down LogicJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Check of Motors/Couplings Pre-Operation ChecksCheck of Electrical Items Pre-Operation Check List Temporary Application of Power2-22 Installation Keypad Key Functions Section OperationFWD Used to initiate a forward direction run of the motor OPERATING CONDITION Keypad Status IndicatorSTATUS INDICATION 3-4 Operation Description of Keypad DisplaysDescription SymbolStop Mode Run ModeProgram Mode Control Operation AdjustmentSecurity Access/Lockout Level One Parameter Adjustments Value Parameter 21-Operating ModeStart Control Type of ControlParameter 21-Operating Mode = 6 or Electronic Pot Control Terminal Logic3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current Value Description 0 Output Off Parameter 71-ANALOG OUTPUT SELECT2 Output Current, Full Scale = 200% of Rated Current 3 Drive Load, Full Scale = 200% of Rated LoadParameter 75-RELAY OUTPUT SELECT Value Description Level Two Parameter Adjustmentsoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation Braking Action / Function DC Braking DisabledParameter 41-Parameter 47-DC BRAKE TIME Fixed Boost Volts/Hertz Profiles100% Square 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Pull-Down Parameter 77-External Trip SelectDescription / Function Parameter 81-Factory Settings Value Description Page Parameter 82-Start Options - Continued Value Description Auto Restart is active after application of line power and RunValue Displayed Diagnostic Displays Section TroubleshootingFault Codes Fault Code Description Troubleshooting MaintenanceIndication Possible CauseIndication adjustedPossible Cause Corrective ActionIndication Ambient temperature tooPossible Cause Corrective Action4-6 Troubleshooting Illustrations Section 5 Illustrations5-2 Illustrations Illustrations 3 & 5 HP NEMA 230 & 460VAC5-4 Illustrations Parameter List Appendix A ParametersFactory Setting User SettingSetting Parameter List ± ContinuedSetting Param501 646±4711 Fax 501 648±5792 BALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400Form 1099A  Baldor Electric Company