Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E manual 3 Typical Connections for M-Contactor

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 22

M-Contactor

M-Contactor

If required by local codes or for safety reasons, an M-Contactor (motor circuit contactor) may be installed. However, incorrect installation or failure of the M-Contactor or wiring may damage the control.

Caution: If an M-Contactor is installed, the control must be disabled at least 20msec before the M-Contactor is opened. If the M-Contactor is opened while the control is supplying voltage and current to the motor, the control may me damaged.

A motor circuit contactor provides a positive disconnect of the motor windings from the control. Opening the M-Contactor ensures that the control cannot drive the motor. This may be required during certain manual operations with the load (like cleaning cutting knives etc.). Figure 2-3 shows how an M-Contactor is connected to the H series control.

Figure 2-3 Typical Connections for M-Contactor

Stop/E-Stop

		M
	M3
	M2	Motor
		Motor
M	M1
	M1

See recommended tightening torques for terminal connectors.

Installation 2-9

Image 22

Baldor ID101F50-E manual 3 Typical Connections for M-Contactor

Contents

Series Inverter Control Installation and Operating Manual 6/98MN710 AC INVERTERTable of Contents Table of ContentsSection SectionSection MOL Terminal Connections16-Load Torque Section Appendix Aiv Table of Contents SectionLimited Warranty Section General InformationSafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Specifications Linear to Squared Reduced in 6 patternsKeypad, 2 Wire, 3 Wire, Preset Speeds 0C to 40C Maximum without deratingAnalog Outputs Fault ConditionsOperator Keypad Relay OutputsRatings 1-8 General Information Section Installation Location and MountingTerminal Access Cover Removal 2-2 InstallationTerminal and Jumper Locations Wiring ConsiderationsFigure 2-2 Terminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Wire Wire Size and Protection DevicesOutput Recommended Terminal Tightening Torques Main Circuit Wiringnameplate. Use of control with wrong power Do not use this control with any inputAC Power Connections Motor Connections 2-8 InstallationM-Contactor Figure 2-3 Typical Connections for M-ContactorLogic Wiring Analog Command InputsOpto Isolated Inputs Analog OutputExternal Trip Connection Jumper J19 Input Selection Jumper J19 SelectionsRelay Outputs Selection Of Operation Mode And Connection DiagramsReference Speed Select 2 Wire Run/Stop ConnectionsFunction Function Ramp SelectSpeed Select FunctionSpeed Select 3 Wire Run/Stop ConnectionsFunction See recommended tightening torques for terminal connectors 2 Wire Run/Stop, Electronic Potentiometer Connections3 Wire Run/Stop, Electronic Potentiometer Connections Parameter 21 - Operating Mode =Relay Output MOL Terminal Connections 77-External Trip SelectAnalog Meter Pull±Down LogicJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Check of Electrical Items Pre-Operation ChecksCheck of Motors/Couplings Temporary Application of Power Pre-Operation Check List2-22 Installation Section Operation Keypad Key FunctionsFWD Used to initiate a forward direction run of the motor STATUS INDICATION Keypad Status IndicatorOPERATING CONDITION Description of Keypad Displays 3-4 OperationStop Mode SymbolDescription Run ModeSecurity Access/Lockout Control Operation AdjustmentProgram Mode Level One Parameter Adjustments Start Control Parameter 21-Operating ModeValue Type of ControlElectronic Pot Control Terminal Logic Parameter 21-Operating Mode = 6 or3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current 2 Output Current, Full Scale = 200% of Rated Current Parameter 71-ANALOG OUTPUT SELECTValue Description 0 Output Off 3 Drive Load, Full Scale = 200% of Rated LoadLevel Two Parameter Adjustments Parameter 75-RELAY OUTPUT SELECT Value Descriptionoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation Parameter 41-Parameter 47-DC BRAKE TIME DC Braking DisabledBraking Action / Function 100% Square Volts/Hertz ProfilesFixed Boost 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Description / Function Parameter 77-External Trip SelectPull-Down Parameter 81-Factory Settings Value Description Page Auto Restart is active after application of line power and Run Parameter 82-Start Options - Continued Value DescriptionValue Displayed Section Troubleshooting Diagnostic DisplaysFault Codes Fault Code Description Indication MaintenanceTroubleshooting Possible CausePossible Cause adjustedIndication Corrective ActionPossible Cause Ambient temperature tooIndication Corrective Action4-6 Troubleshooting Section 5 Illustrations Illustrations5-2 Illustrations 3 & 5 HP NEMA 230 & 460VAC Illustrations5-4 Illustrations Factory Setting Appendix A ParametersParameter List User SettingSetting Parameter List ± ContinuedSetting ParamForm 1099A BALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400501 646±4711 Fax 501 648±5792  Baldor Electric Company