Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E manual Ratings

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 12

Ratings

Ratings

Catalog No.

HP

(kW)

	Input			Output
VAC		Amps	Volts	Amps	Amps
			VAC	Cont *	Peak

ID101F50-E	0.5	115	4.5	230	2.2	3.3
	(0.37)

ID10101-E	1.0	115	8.9	230	4.0	6.0
	(0.75)

ID102F50-E	0.5	230	1.9	230	2.2	3.3
	(0.37)

ID10201-E	1.0	230	3.8	230	4.0	6.0
	(0.75)

ID10202-E	2.0	230	7.5	230	7.5	11.3
	(1.5)

ID10203-E	3.0	230	10.4	230	10.6	15.9
	(2.2)

ID10205-E	5.0	230	17.6	230	16.7	25.1
	(3.7)

ID10401-E	1.0	460	2.3	460	2.2	3.3
	(0.75)

ID10402-E	2.0	460	5.1	460	4.1	6.2
	(1.5)

ID10403-E	3.0	460	6.2	460	6.1	9.2
	(2.2)

ID10405-E	5.0	460	10.8	460	9.9	14.9
	(3.7)

*Rating equals 1.1 times parameter 03-Rated Current value.

Note: 230VAC three phase units can be operated at 115VAC single phase power if the output current AMPS (Continuous and Peak) are derated by 25%.

General Information 1-7

Image 12

Baldor ID101F50-E manual Ratings

Contents

6/98 MN710Series Inverter Control Installation and Operating Manual AC INVERTERTable of Contents SectionTable of Contents SectionSection MOL Terminal Connections16-Load Torque Appendix A iv Table of ContentsSection SectionLimited Warranty Section General InformationSafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Specifications Linear to Squared Reduced in 6 patternsKeypad, 2 Wire, 3 Wire, Preset Speeds 0C to 40C Maximum without deratingFault Conditions Operator KeypadAnalog Outputs Relay OutputsRatings 1-8 General Information Section Installation Location and MountingTerminal Access Cover Removal 2-2 InstallationWiring Considerations Terminal and Jumper LocationsFigure 2-2 Terminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Wire Size and Protection Devices WireOutput Main Circuit Wiring nameplate. Use of control with wrong powerRecommended Terminal Tightening Torques Do not use this control with any inputAC Power Connections Motor Connections 2-8 InstallationM-Contactor Figure 2-3 Typical Connections for M-ContactorLogic Wiring Analog Command InputsAnalog Output Opto Isolated InputsExternal Trip Connection Jumper J19 Input Selection Jumper J19 SelectionsSelection Of Operation Mode And Connection Diagrams Relay OutputsReference 2 Wire Run/Stop Connections Speed SelectFunction Ramp Select Speed SelectFunction Function3 Wire Run/Stop Connections Speed SelectFunction 2 Wire Run/Stop, Electronic Potentiometer Connections 3 Wire Run/Stop, Electronic Potentiometer ConnectionsSee recommended tightening torques for terminal connectors Parameter 21 - Operating Mode =MOL Terminal Connections 77-External Trip Select Analog MeterRelay Output Pull±Down LogicJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Pre-Operation Checks Check of Electrical ItemsCheck of Motors/Couplings Temporary Application of Power Pre-Operation Check List2-22 Installation Section Operation Keypad Key FunctionsFWD Used to initiate a forward direction run of the motor Keypad Status Indicator STATUS INDICATIONOPERATING CONDITION Description of Keypad Displays 3-4 OperationSymbol DescriptionStop Mode Run ModeControl Operation Adjustment Security Access/LockoutProgram Mode Level One Parameter Adjustments Parameter 21-Operating Mode ValueStart Control Type of ControlElectronic Pot Control Terminal Logic Parameter 21-Operating Mode = 6 or3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current Parameter 71-ANALOG OUTPUT SELECT Value Description 0 Output Off2 Output Current, Full Scale = 200% of Rated Current 3 Drive Load, Full Scale = 200% of Rated LoadLevel Two Parameter Adjustments Parameter 75-RELAY OUTPUT SELECT Value Descriptionoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation DC Braking Disabled Parameter 41-Parameter 47-DC BRAKE TIMEBraking Action / Function Volts/Hertz Profiles 100% SquareFixed Boost 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Parameter 77-External Trip Select Description / FunctionPull-Down Parameter 81-Factory Settings Value Description Page Auto Restart is active after application of line power and Run Parameter 82-Start Options - Continued Value DescriptionValue Displayed Section Troubleshooting Diagnostic DisplaysFault Codes Fault Code Description Maintenance TroubleshootingIndication Possible Causeadjusted IndicationPossible Cause Corrective ActionAmbient temperature too IndicationPossible Cause Corrective Action4-6 Troubleshooting Section 5 Illustrations Illustrations5-2 Illustrations 3 & 5 HP NEMA 230 & 460VAC Illustrations5-4 Illustrations Appendix A Parameters Parameter ListFactory Setting User SettingParameter List ± Continued SettingSetting ParamBALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400 501 646±4711 Fax 501 648±5792Form 1099A  Baldor Electric Company