Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E manual Wire Size and Protection Devices, Output

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 18

Wire Size and Protection Devices

Caution: Do not use power factor correction capacitors on the input power lines to the inverter or damage to the control may result.

All external control wiring to the inverter should be run in a separate conduit from all other wiring. The use of shielded twisted pair wire is recommended for all control wiring. The shield of the control wiring should be connected to control terminal CM of the inverter only. The other end of the shield should be taped to the wire jacket to prevent electrical shorts.

Conduit openings are provided at the bottom of the inverter housing to allow power and control wiring entrance to the control. Please refer to the inverter outline drawings located in Section 5 of this manual for sizes of the conduit openings.

The following tables show recommended wire size and protection devices along with recommended terminal tightening torques.

Wire Size and Protection Devices

		Rated	Input/	Input	Input Fuses
	Catalog No.	Rated	Output	Input
	Catalog No.	HP	Wire	Breaker	Fast	Time
		HP	Wire	Breaker	Fast	Time
			AWG Cu		Acting	Delay
					Acting	Delay
	ID101F50-E	0.5	14	240V/10A	240V/5A	240V/3A
	ID10101-E	1	14	240V/15A	240V/10A	240V/6A
	ID102F50-E	0.5	14	240V/10A	240V/5A	240V/3A
	ID10201-E	1	14	240V/15A	240V/10A	240V/6A
	ID10202-E	2	14	240V/20A	240V/20A	240V/12A
	ID10203-E	3	14	240V/25	240V/25	240V/15
	ID10205-E	5	12	240V/40	240V/35	240V/25
	ID10401-E	1	14	480V/5A	480V/5A	480V/6A
	ID10402-E	2	14	480V/10A	480V/10A	480V/12A

	ID10403-E	3	14	480V/15	480V/15	480V/15
	ID10405-E	5	14	480V/20	480V/20	480V/25

Input and output wire size is based on use of 60/75°C rated copper conductor wire.

Installation 2-5

Image 18

Baldor ID101F50-E manual Wire Size and Protection Devices, Output

Contents

Series Inverter Control Installation and Operating Manual 6/98MN710 AC INVERTERTable of Contents Table of ContentsSection SectionSection MOL Terminal Connections16-Load Torque Section Appendix Aiv Table of Contents SectionLimited Warranty Section General InformationSafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Specifications Linear to Squared Reduced in 6 patternsKeypad, 2 Wire, 3 Wire, Preset Speeds 0C to 40C Maximum without deratingAnalog Outputs Fault ConditionsOperator Keypad Relay OutputsRatings 1-8 General Information Section Installation Location and MountingTerminal Access Cover Removal 2-2 InstallationWiring Considerations Terminal and Jumper LocationsFigure 2-2 Terminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Wire Size and Protection Devices WireOutput Recommended Terminal Tightening Torques Main Circuit Wiringnameplate. Use of control with wrong power Do not use this control with any inputAC Power Connections Motor Connections 2-8 InstallationM-Contactor Figure 2-3 Typical Connections for M-ContactorLogic Wiring Analog Command InputsAnalog Output Opto Isolated InputsExternal Trip Connection Jumper J19 Input Selection Jumper J19 SelectionsSelection Of Operation Mode And Connection Diagrams Relay OutputsReference 2 Wire Run/Stop Connections Speed SelectFunction Function Ramp SelectSpeed Select Function3 Wire Run/Stop Connections Speed SelectFunction See recommended tightening torques for terminal connectors 2 Wire Run/Stop, Electronic Potentiometer Connections3 Wire Run/Stop, Electronic Potentiometer Connections Parameter 21 - Operating Mode =Relay Output MOL Terminal Connections 77-External Trip SelectAnalog Meter Pull±Down LogicJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Pre-Operation Checks Check of Electrical ItemsCheck of Motors/Couplings Temporary Application of Power Pre-Operation Check List2-22 Installation Section Operation Keypad Key FunctionsFWD Used to initiate a forward direction run of the motor Keypad Status Indicator STATUS INDICATIONOPERATING CONDITION Description of Keypad Displays 3-4 OperationStop Mode SymbolDescription Run ModeControl Operation Adjustment Security Access/LockoutProgram Mode Level One Parameter Adjustments Start Control Parameter 21-Operating ModeValue Type of ControlElectronic Pot Control Terminal Logic Parameter 21-Operating Mode = 6 or3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current 2 Output Current, Full Scale = 200% of Rated Current Parameter 71-ANALOG OUTPUT SELECTValue Description 0 Output Off 3 Drive Load, Full Scale = 200% of Rated LoadLevel Two Parameter Adjustments Parameter 75-RELAY OUTPUT SELECT Value Descriptionoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation DC Braking Disabled Parameter 41-Parameter 47-DC BRAKE TIMEBraking Action / Function Volts/Hertz Profiles 100% SquareFixed Boost 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Parameter 77-External Trip Select Description / FunctionPull-Down Parameter 81-Factory Settings Value Description Page Auto Restart is active after application of line power and Run Parameter 82-Start Options - Continued Value DescriptionValue Displayed Section Troubleshooting Diagnostic DisplaysFault Codes Fault Code Description Indication MaintenanceTroubleshooting Possible CausePossible Cause adjustedIndication Corrective ActionCorrective Action IndicationPossible Cause Input voltage too high4-6 Troubleshooting Section 5 Illustrations Illustrations5-2 Illustrations 3 & 5 HP NEMA 230 & 460VAC Illustrations5-4 Illustrations Factory Setting Appendix A ParametersParameter List User SettingSetting Parameter List ± ContinuedSetting ParamForm 1099A BALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400501 646±4711 Fax 501 648±5792  Baldor Electric Company