Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E Operator Keypad, Analog Outputs, Relay Outputs, Fault Conditions, Input Voltage

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 11

Operator Keypad

Operator Keypad

Display	Custom Backlit LCD
Keypad	8 Key with Tactile Feel
Functions	Output Status Monitoring, Digital Speed Control,
	Parameter Setting and Display and Fault Log
	Display
LED Indicators	Red/Green for Status
Analog Outputs
Analog Outputs	1 Assignable
Full Scale Range	0 to 10VDC Maximum
Output Conditions	3 conditions plus calibration
	(see Analog Output Table)
Relay Outputs
Relay Outputs	1 Assignable
Rated Voltage	115VAC
Rated Current	1 Ampere Maximum
Conditions	10 conditions (see Relay Output Table)
Fault Conditions
Automatic Shutdown	15 conditions (see Fault Code Table)

Watts Loss Data

Catalog No. Horsepower

Input

Voltage

Total Watts Loss

Single Phase	Three Phase
Input	Input

ID101F50-E	0.5 1PH	115	24	N/A
ID10101-E	1.0 1PH	115	42	N/A

ID102F50-E	0.5 3PH	230	16	19
ID10201-E	1.0 3PH	230	28	37

ID10202-E	2.0 3PH	230	52	66
ID102	3.0 3PH	230	66	70
ID102	5.0 3PH	230	70	129
ID10401-E	1.0 3PH	460	N/A	40
ID10402-E	2.0 3PH	460	N/A	67
ID104	3.0 3PH	460	N/A	118
ID104	5.0 3PH	460	N/A	184

1-6 General Information

Image 11

Baldor ID101F50-E manual Operator Keypad, Analog Outputs, Relay Outputs, Fault Conditions, Watts Loss Data, Input Voltage

Contents

AC INVERTER 6/98MN710 Series Inverter Control Installation and Operating ManualSection Table of ContentsSection Table of ContentsMOL Terminal Connections Section16-Load Torque Section Appendix Aiv Table of Contents SectionSection General Information Limited WarrantySafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Linear to Squared Reduced in 6 patterns Specifications0C to 40C Maximum without derating Keypad, 2 Wire, 3 Wire, Preset SpeedsRelay Outputs Fault ConditionsOperator Keypad Analog OutputsRatings 1-8 General Information Location and Mounting Section Installation2-2 Installation Terminal Access Cover RemovalFigure 2-2 Terminal and Jumper Locations Wiring ConsiderationsTerminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Output Wire Size and Protection DevicesWire Do not use this control with any input Main Circuit Wiringnameplate. Use of control with wrong power Recommended Terminal Tightening TorquesAC Power Connections 2-8 Installation Motor ConnectionsFigure 2-3 Typical Connections for M-Contactor M-ContactorAnalog Command Inputs Logic WiringExternal Trip Connection Analog OutputOpto Isolated Inputs Jumper J19 Selections Jumper J19 Input SelectionReference Selection Of Operation Mode And Connection DiagramsRelay Outputs Function 2 Wire Run/Stop ConnectionsSpeed Select Function Ramp SelectSpeed Select FunctionFunction 3 Wire Run/Stop ConnectionsSpeed Select Parameter 21 - Operating Mode = 2 Wire Run/Stop, Electronic Potentiometer Connections3 Wire Run/Stop, Electronic Potentiometer Connections See recommended tightening torques for terminal connectorsPull±Down Logic MOL Terminal Connections 77-External Trip SelectAnalog Meter Relay OutputJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Check of Motors/Couplings Pre-Operation ChecksCheck of Electrical Items Pre-Operation Check List Temporary Application of Power2-22 Installation Keypad Key Functions Section OperationFWD Used to initiate a forward direction run of the motor OPERATING CONDITION Keypad Status IndicatorSTATUS INDICATION 3-4 Operation Description of Keypad DisplaysRun Mode SymbolDescription Stop ModeProgram Mode Control Operation AdjustmentSecurity Access/Lockout Level One Parameter Adjustments Type of Control Parameter 21-Operating ModeValue Start ControlParameter 21-Operating Mode = 6 or Electronic Pot Control Terminal Logic3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current 3 Drive Load, Full Scale = 200% of Rated Load Parameter 71-ANALOG OUTPUT SELECTValue Description 0 Output Off 2 Output Current, Full Scale = 200% of Rated CurrentParameter 75-RELAY OUTPUT SELECT Value Description Level Two Parameter Adjustmentsoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation Braking Action / Function DC Braking DisabledParameter 41-Parameter 47-DC BRAKE TIME Fixed Boost Volts/Hertz Profiles100% Square 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Pull-Down Parameter 77-External Trip SelectDescription / Function Parameter 81-Factory Settings Value Description Page Parameter 82-Start Options - Continued Value Description Auto Restart is active after application of line power and RunValue Displayed Diagnostic Displays Section TroubleshootingFault Codes Fault Code Description Possible Cause MaintenanceTroubleshooting IndicationCorrective Action adjustedIndication Possible CauseCorrective Action Ambient temperature tooIndication Possible Cause4-6 Troubleshooting Illustrations Section 5 Illustrations5-2 Illustrations Illustrations 3 & 5 HP NEMA 230 & 460VAC5-4 Illustrations User Setting Appendix A ParametersParameter List Factory SettingParam Parameter List ± ContinuedSetting Setting Baldor Electric Company BALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400501 646±4711 Fax 501 648±5792 Form 1099A