Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E Pre-Operation Checks, Check of Electrical Items, Check of Motors/Couplings

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 33

Pre-Operation Checks

Pre-Operation Checks

Check of Electrical Items

After completing all the installation steps and before applying line power to the system, carefully check the following items:

1.Verify AC line voltage at source matches control rating.

2.Inspect all power terminations for workmanship and tightness.

3.Verify control and motor are grounded to each other and the control is connected to earth ground.

4.Check incoming signal wiring for accuracy.

Be certain all brake coils, contactors, and relay coils have noise suppression. This should be an R-C filter for AC coils and reverse polarity diodes for DC coils. MOV type transient suppression is not adequate.

WARNING: MAKE SURE THAT UNEXPECTED OPERATION OF THE MOTOR SHAFT DURING START-UP WILL NOT CAUSE INJURY TO PERSONNEL OR DAMAGE TO EQUIPMENT.

Check of Motors/Couplings

Verify freedom of motion for all motor shafts and that all motor couplings are tight without backlash.

Verify the holding brakes, if any, are properly adjusted to fully release and set to the desired torque value.

2-20 Installation

Image 33

Baldor ID101F50-E manual Pre-Operation Checks, Check of Electrical Items, Check of Motors/Couplings

Contents

MN710 6/98Series Inverter Control Installation and Operating Manual AC INVERTERSection Table of ContentsTable of Contents SectionMOL Terminal Connections Section16-Load Torque iv Table of Contents Appendix ASection SectionSection General Information Limited WarrantySafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Linear to Squared Reduced in 6 patterns Specifications0C to 40C Maximum without derating Keypad, 2 Wire, 3 Wire, Preset SpeedsOperator Keypad Fault ConditionsAnalog Outputs Relay OutputsRatings 1-8 General Information Location and Mounting Section Installation2-2 Installation Terminal Access Cover RemovalWiring Considerations Terminal and Jumper LocationsFigure 2-2 Terminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Wire Size and Protection Devices WireOutput nameplate. Use of control with wrong power Main Circuit WiringRecommended Terminal Tightening Torques Do not use this control with any inputAC Power Connections 2-8 Installation Motor ConnectionsFigure 2-3 Typical Connections for M-Contactor M-ContactorAnalog Command Inputs Logic WiringAnalog Output Opto Isolated InputsExternal Trip Connection Jumper J19 Selections Jumper J19 Input SelectionSelection Of Operation Mode And Connection Diagrams Relay OutputsReference 2 Wire Run/Stop Connections Speed SelectFunction Speed Select Ramp SelectFunction Function3 Wire Run/Stop Connections Speed SelectFunction 3 Wire Run/Stop, Electronic Potentiometer Connections 2 Wire Run/Stop, Electronic Potentiometer ConnectionsSee recommended tightening torques for terminal connectors Parameter 21 - Operating Mode =Analog Meter MOL Terminal Connections 77-External Trip SelectRelay Output Pull±Down LogicJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Pre-Operation Checks Check of Electrical ItemsCheck of Motors/Couplings Pre-Operation Check List Temporary Application of Power2-22 Installation Keypad Key Functions Section OperationFWD Used to initiate a forward direction run of the motor Keypad Status Indicator STATUS INDICATIONOPERATING CONDITION 3-4 Operation Description of Keypad DisplaysDescription SymbolStop Mode Run ModeControl Operation Adjustment Security Access/LockoutProgram Mode Level One Parameter Adjustments Value Parameter 21-Operating ModeStart Control Type of ControlParameter 21-Operating Mode = 6 or Electronic Pot Control Terminal Logic3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current Value Description 0 Output Off Parameter 71-ANALOG OUTPUT SELECT2 Output Current, Full Scale = 200% of Rated Current 3 Drive Load, Full Scale = 200% of Rated LoadParameter 75-RELAY OUTPUT SELECT Value Description Level Two Parameter Adjustmentsoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation DC Braking Disabled Parameter 41-Parameter 47-DC BRAKE TIMEBraking Action / Function Volts/Hertz Profiles 100% SquareFixed Boost 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Parameter 77-External Trip Select Description / FunctionPull-Down Parameter 81-Factory Settings Value Description Page Parameter 82-Start Options - Continued Value Description Auto Restart is active after application of line power and RunValue Displayed Diagnostic Displays Section TroubleshootingFault Codes Fault Code Description Troubleshooting MaintenanceIndication Possible CauseIndication adjustedPossible Cause Corrective ActionIndication Ambient temperature tooPossible Cause Corrective Action4-6 Troubleshooting Illustrations Section 5 Illustrations5-2 Illustrations Illustrations 3 & 5 HP NEMA 230 & 460VAC5-4 Illustrations Parameter List Appendix A ParametersFactory Setting User SettingSetting Parameter List ± ContinuedSetting Param501 646±4711 Fax 501 648±5792 BALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400Form 1099A  Baldor Electric Company