Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E manual Terminal Access Cover Removal, Installation

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 15

Terminal Access Cover Removal

Terminal Access Cover Removal

To remove the Terminal Access Cover insert a small blade screwdriver into the slots located on the lower left and right hand corners of the access cover. Use a slight twisting motion while lifting upward to loosen one side. Use the same motion to loosen the other side then lift the cover off of the control. To reinstall, simply snap the cover back into place. See Figure 2-1 below.

Figure 2-1

2-2 Installation

Image 15

Baldor ID101F50-E manual Terminal Access Cover Removal, Installation

Contents

AC INVERTER 6/98MN710 Series Inverter Control Installation and Operating ManualSection Table of ContentsSection Table of ContentsMOL Terminal Connections Section16-Load Torque Section Appendix Aiv Table of Contents SectionSection General Information Limited WarrantySafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Linear to Squared Reduced in 6 patterns Specifications0C to 40C Maximum without derating Keypad, 2 Wire, 3 Wire, Preset SpeedsRelay Outputs Fault ConditionsOperator Keypad Analog OutputsRatings 1-8 General Information Location and Mounting Section Installation2-2 Installation Terminal Access Cover RemovalWiring Considerations Terminal and Jumper LocationsFigure 2-2 Terminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Wire Size and Protection Devices WireOutput Do not use this control with any input Main Circuit Wiringnameplate. Use of control with wrong power Recommended Terminal Tightening TorquesAC Power Connections 2-8 Installation Motor ConnectionsFigure 2-3 Typical Connections for M-Contactor M-ContactorAnalog Command Inputs Logic WiringAnalog Output Opto Isolated InputsExternal Trip Connection Jumper J19 Selections Jumper J19 Input SelectionSelection Of Operation Mode And Connection Diagrams Relay OutputsReference 2 Wire Run/Stop Connections Speed SelectFunction Function Ramp SelectSpeed Select Function3 Wire Run/Stop Connections Speed SelectFunction Parameter 21 - Operating Mode = 2 Wire Run/Stop, Electronic Potentiometer Connections3 Wire Run/Stop, Electronic Potentiometer Connections See recommended tightening torques for terminal connectorsPull±Down Logic MOL Terminal Connections 77-External Trip SelectAnalog Meter Relay OutputJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Pre-Operation Checks Check of Electrical ItemsCheck of Motors/Couplings Pre-Operation Check List Temporary Application of Power2-22 Installation Keypad Key Functions Section OperationFWD Used to initiate a forward direction run of the motor Keypad Status Indicator STATUS INDICATIONOPERATING CONDITION 3-4 Operation Description of Keypad DisplaysRun Mode SymbolDescription Stop ModeControl Operation Adjustment Security Access/LockoutProgram Mode Level One Parameter Adjustments Type of Control Parameter 21-Operating ModeValue Start ControlParameter 21-Operating Mode = 6 or Electronic Pot Control Terminal Logic3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current 3 Drive Load, Full Scale = 200% of Rated Load Parameter 71-ANALOG OUTPUT SELECTValue Description 0 Output Off 2 Output Current, Full Scale = 200% of Rated CurrentParameter 75-RELAY OUTPUT SELECT Value Description Level Two Parameter Adjustmentsoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation DC Braking Disabled Parameter 41-Parameter 47-DC BRAKE TIMEBraking Action / Function Volts/Hertz Profiles 100% SquareFixed Boost 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Parameter 77-External Trip Select Description / FunctionPull-Down Parameter 81-Factory Settings Value Description Page Parameter 82-Start Options - Continued Value Description Auto Restart is active after application of line power and RunValue Displayed Diagnostic Displays Section TroubleshootingFault Codes Fault Code Description Possible Cause MaintenanceTroubleshooting IndicationCorrective Action adjustedIndication Possible CauseCorrective Action Ambient temperature tooIndication Possible Cause4-6 Troubleshooting Illustrations Section 5 Illustrations5-2 Illustrations Illustrations 3 & 5 HP NEMA 230 & 460VAC5-4 Illustrations User Setting Appendix A ParametersParameter List Factory SettingParam Parameter List ± ContinuedSetting Setting Baldor Electric Company BALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400501 646±4711 Fax 501 648±5792 Form 1099A