Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E manual Appendix A Parameters, Parameter List, Param Parameter Description No

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 72

Appendix A

Appendix A

Parameters

Parameter List

Param Parameter Description No.

Adj.

Range

Factory Setting

User

Setting

02	Software revision	View only	View only
03	Rated current	View only	View only
07	Last fault	View only	View only
08	Second fault	View only	View only
09	First fault	View only	View only
12	Output frequency	View only	View only
13	Output voltage	View only	View only
14	Output current	View only	View only
15	Drive load	View only	View only
16	Load torque	View only	View only
17	Heatsink temperature	View only	View only
21	Operating mode	0-11	0
24	Analog command select	0-3	0
31	Min. output frequency	0.1-400Hz	0Hz
32	Max. output frequency	20-400Hz	60Hz
33	Preset speed #1	0.1-400Hz	5Hz
34	Preset speed #2	0.1-400Hz	20Hz
35	Preset speed #3	0.1-400Hz	40Hz
36	Preset speed #4	0.1-400Hz	60Hz
37	Preset speed #5	0.1-400Hz	0Hz
38	Preset speed #6	0.1-400Hz	0Hz
39	Minimum frequency	0.1-400Hz	10Hz
	torque limit
41	Accel/Decel/Coast select	0-7	0
42	Accel Time #1	.1-600sec	3sec
43	Decel Time #1	.1-600sec	3sec
44	Accel Time #2	.1-600sec	1sec
45	Decel Time #2	.1-600sec	1sec
46	Decel Time Torque limit	.1-30sec	1sec

Level 2 parameters are shaded.

Parameters A-1

Image 72

Baldor ID101F50-E manual Appendix A Parameters, Parameter List, Param Parameter Description No, Adj Range, Factory Setting

Contents

6/98 MN710Series Inverter Control Installation and Operating Manual AC INVERTERTable of Contents SectionTable of Contents SectionSection MOL Terminal Connections16-Load Torque Appendix A iv Table of ContentsSection SectionLimited Warranty Section General InformationSafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Specifications Linear to Squared Reduced in 6 patternsKeypad, 2 Wire, 3 Wire, Preset Speeds 0C to 40C Maximum without deratingFault Conditions Operator KeypadAnalog Outputs Relay OutputsRatings 1-8 General Information Section Installation Location and MountingTerminal Access Cover Removal 2-2 InstallationWiring Considerations Terminal and Jumper LocationsFigure 2-2 Terminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Wire Size and Protection Devices WireOutput Main Circuit Wiring nameplate. Use of control with wrong powerRecommended Terminal Tightening Torques Do not use this control with any inputAC Power Connections Motor Connections 2-8 InstallationM-Contactor Figure 2-3 Typical Connections for M-ContactorLogic Wiring Analog Command InputsAnalog Output Opto Isolated InputsExternal Trip Connection Jumper J19 Input Selection Jumper J19 SelectionsSelection Of Operation Mode And Connection Diagrams Relay OutputsReference 2 Wire Run/Stop Connections Speed SelectFunction Ramp Select Speed SelectFunction Function3 Wire Run/Stop Connections Speed SelectFunction 2 Wire Run/Stop, Electronic Potentiometer Connections 3 Wire Run/Stop, Electronic Potentiometer ConnectionsSee recommended tightening torques for terminal connectors Parameter 21 - Operating Mode =MOL Terminal Connections 77-External Trip Select Analog MeterRelay Output Pull±Down LogicJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Pre-Operation Checks Check of Electrical ItemsCheck of Motors/Couplings Temporary Application of Power Pre-Operation Check List2-22 Installation Section Operation Keypad Key FunctionsFWD Used to initiate a forward direction run of the motor Keypad Status Indicator STATUS INDICATIONOPERATING CONDITION Description of Keypad Displays 3-4 OperationSymbol DescriptionStop Mode Run ModeControl Operation Adjustment Security Access/LockoutProgram Mode Level One Parameter Adjustments Parameter 21-Operating Mode ValueStart Control Type of ControlElectronic Pot Control Terminal Logic Parameter 21-Operating Mode = 6 or3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current Parameter 71-ANALOG OUTPUT SELECT Value Description 0 Output Off2 Output Current, Full Scale = 200% of Rated Current 3 Drive Load, Full Scale = 200% of Rated LoadLevel Two Parameter Adjustments Parameter 75-RELAY OUTPUT SELECT Value Descriptionoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation DC Braking Disabled Parameter 41-Parameter 47-DC BRAKE TIMEBraking Action / Function Volts/Hertz Profiles 100% SquareFixed Boost 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Parameter 77-External Trip Select Description / FunctionPull-Down Parameter 81-Factory Settings Value Description Page Auto Restart is active after application of line power and Run Parameter 82-Start Options - Continued Value DescriptionValue Displayed Section Troubleshooting Diagnostic DisplaysFault Codes Fault Code Description Maintenance TroubleshootingIndication Possible Causeadjusted IndicationPossible Cause Corrective ActionAmbient temperature too IndicationPossible Cause Corrective Action4-6 Troubleshooting Section 5 Illustrations Illustrations5-2 Illustrations 3 & 5 HP NEMA 230 & 460VAC Illustrations5-4 Illustrations Appendix A Parameters Parameter ListFactory Setting User SettingParameter List ± Continued SettingSetting ParamBALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400 501 646±4711 Fax 501 648±5792Form 1099A  Baldor Electric Company