Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E manual FWD Used to initiate a forward direction run of the motor

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 37

FWD Used to initiate a forward direction run of the motor.

STOP Push to initiate a stop command. Depending on the setup of the control the motor will either ramp (Regen) or Coast to Stop. See 41-Accel/Decel/Coast Select in Section 3 for more information.

FWD Used to initiate a forward direction run of the motor.

REV Used to initiate a reverse direction run of the motor.

PROG Used to access Level 1 Parameters. Holding the SHIFT key then pressing the PROG key will access Level 2 Parameters. If in the Run Mode the control will only allow viewing of the parameter values. Any attempt to change a parameter value while in the Run Mode will result in the display showing ª-----º. If in the Stop Mode pressing PROG or holding

SHIFT then pressing PROG will enter the Programming Mode at Level 1 and Level 2 Parameters respectively. Pressing the PROG key while in the Programming Mode will return the control to the Stop Mode.

SHIFT Used in the Program Mode to allow changing of a parameter value. While in Program Mode, the factory preset value may be reset for any parameter by pressing the SHIFT key then the UP and DOWN ARROW keys simultaneously. The New parameter value is stored when the ENTER key is pressed.

UP ARROW Used to change the displayed parameter or parameter value up one increment. In the Programming Mode the displayed parameters or parameter values will increment up until the highest possible value is reached. The UP Arrow is also used to increment the set speed in the Stop Mode and increment the actual speed in the Run Mode. The value will increase at a faster rate after holding the UP Arrow key for 5 seconds. Pressing SHIFT while holding the UP Arrow will bypass the 5 second delay.

DOWN ARROW Used to change the displayed parameter or parameter value down one increment. In the Programming Mode the displayed parameters or parameter values will increment down until the lowest possible value is reached. The DOWN

3-2 Operation

Image 37

Baldor ID101F50-E manual FWD Used to initiate a forward direction run of the motor

Contents

MN710 6/98Series Inverter Control Installation and Operating Manual AC INVERTERSection Table of ContentsTable of Contents SectionMOL Terminal Connections Section16-Load Torque iv Table of Contents Appendix ASection SectionSection General Information Limited WarrantySafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Linear to Squared Reduced in 6 patterns Specifications0C to 40C Maximum without derating Keypad, 2 Wire, 3 Wire, Preset SpeedsOperator Keypad Fault ConditionsAnalog Outputs Relay OutputsRatings 1-8 General Information Location and Mounting Section Installation2-2 Installation Terminal Access Cover RemovalTerminal and Jumper Locations Wiring ConsiderationsFigure 2-2 Terminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Wire Wire Size and Protection DevicesOutput nameplate. Use of control with wrong power Main Circuit WiringRecommended Terminal Tightening Torques Do not use this control with any inputAC Power Connections 2-8 Installation Motor ConnectionsFigure 2-3 Typical Connections for M-Contactor M-ContactorAnalog Command Inputs Logic WiringOpto Isolated Inputs Analog OutputExternal Trip Connection Jumper J19 Selections Jumper J19 Input SelectionRelay Outputs Selection Of Operation Mode And Connection DiagramsReference Speed Select 2 Wire Run/Stop ConnectionsFunction Speed Select Ramp SelectFunction FunctionSpeed Select 3 Wire Run/Stop ConnectionsFunction 3 Wire Run/Stop, Electronic Potentiometer Connections 2 Wire Run/Stop, Electronic Potentiometer ConnectionsSee recommended tightening torques for terminal connectors Parameter 21 - Operating Mode =Analog Meter MOL Terminal Connections 77-External Trip SelectRelay Output Pull±Down LogicJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Check of Electrical Items Pre-Operation ChecksCheck of Motors/Couplings Pre-Operation Check List Temporary Application of Power2-22 Installation Keypad Key Functions Section OperationFWD Used to initiate a forward direction run of the motor STATUS INDICATION Keypad Status IndicatorOPERATING CONDITION 3-4 Operation Description of Keypad DisplaysDescription SymbolStop Mode Run ModeSecurity Access/Lockout Control Operation AdjustmentProgram Mode Level One Parameter Adjustments Value Parameter 21-Operating ModeStart Control Type of ControlParameter 21-Operating Mode = 6 or Electronic Pot Control Terminal Logic3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current Value Description 0 Output Off Parameter 71-ANALOG OUTPUT SELECT2 Output Current, Full Scale = 200% of Rated Current 3 Drive Load, Full Scale = 200% of Rated LoadParameter 75-RELAY OUTPUT SELECT Value Description Level Two Parameter Adjustmentsoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation Parameter 41-Parameter 47-DC BRAKE TIME DC Braking DisabledBraking Action / Function 100% Square Volts/Hertz ProfilesFixed Boost 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Description / Function Parameter 77-External Trip SelectPull-Down Parameter 81-Factory Settings Value Description Page Parameter 82-Start Options - Continued Value Description Auto Restart is active after application of line power and RunValue Displayed Diagnostic Displays Section TroubleshootingFault Codes Fault Code Description Troubleshooting MaintenanceIndication Possible CauseIndication adjustedPossible Cause Corrective ActionIndication Ambient temperature tooPossible Cause Corrective Action4-6 Troubleshooting Illustrations Section 5 Illustrations5-2 Illustrations Illustrations 3 & 5 HP NEMA 230 & 460VAC5-4 Illustrations Parameter List Appendix A ParametersFactory Setting User SettingSetting Parameter List ± ContinuedSetting Param501 646±4711 Fax 501 648±5792 BALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400Form 1099A  Baldor Electric Company