Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E manual Wire Run/Stop Connections, Speed Select, Function

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 29

3 Wire Run/Stop Connections

3 Wire Run/Stop Connections

Parameter 21 - Operating Mode = 4 or 5

		CM
Forward	Shield	FWD
		FWD
Reverse		REV
		REV
Stop		PS3
		PS3
Speed Select		PS2
		PS2
Speed Select		PS1
		PS1
		V+
J19		MOL
J19

Pull±Up Logic

	Shield
	CM
Forward	FWD
	FWD
Reverse	REV
	REV
Stop	PS3
	PS3
Speed Select	PS2
	PS2
Speed Select	PS1
	PS1
	V+
J19	MOL
J19

Pull±Down Logic

See recommended tightening torques for terminal connectors.

Speed Select

PS2	PS1	Function
Open	Open	Keypad or
		Analog Command Input
Open	Closed	33 - Preset Speed #1
Closed	Open	34 - Preset Speed #2
Closed	Closed	35 - Preset Speed #3

2-16 Installation

Image 29

Baldor ID101F50-E manual Wire Run/Stop Connections, Speed Select, Function

Contents

MN710 6/98Series Inverter Control Installation and Operating Manual AC INVERTERSection Table of ContentsTable of Contents SectionMOL Terminal Connections Section16-Load Torque iv Table of Contents Appendix ASection SectionSection General Information Limited WarrantySafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Linear to Squared Reduced in 6 patterns Specifications0C to 40C Maximum without derating Keypad, 2 Wire, 3 Wire, Preset SpeedsOperator Keypad Fault ConditionsAnalog Outputs Relay OutputsRatings 1-8 General Information Location and Mounting Section Installation2-2 Installation Terminal Access Cover RemovalFigure 2-2 Terminal and Jumper Locations Wiring ConsiderationsTerminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Output Wire Size and Protection DevicesWire nameplate. Use of control with wrong power Main Circuit WiringRecommended Terminal Tightening Torques Do not use this control with any inputAC Power Connections 2-8 Installation Motor ConnectionsFigure 2-3 Typical Connections for M-Contactor M-ContactorAnalog Command Inputs Logic WiringExternal Trip Connection Analog OutputOpto Isolated Inputs Jumper J19 Selections Jumper J19 Input SelectionReference Selection Of Operation Mode And Connection DiagramsRelay Outputs Function 2 Wire Run/Stop ConnectionsSpeed Select Speed Select Ramp SelectFunction FunctionFunction 3 Wire Run/Stop ConnectionsSpeed Select 3 Wire Run/Stop, Electronic Potentiometer Connections 2 Wire Run/Stop, Electronic Potentiometer ConnectionsSee recommended tightening torques for terminal connectors Parameter 21 - Operating Mode =Analog Meter MOL Terminal Connections 77-External Trip SelectRelay Output Pull±Down LogicJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Check of Motors/Couplings Pre-Operation ChecksCheck of Electrical Items Pre-Operation Check List Temporary Application of Power2-22 Installation Keypad Key Functions Section OperationFWD Used to initiate a forward direction run of the motor OPERATING CONDITION Keypad Status IndicatorSTATUS INDICATION 3-4 Operation Description of Keypad DisplaysDescription SymbolStop Mode Run ModeProgram Mode Control Operation AdjustmentSecurity Access/Lockout Level One Parameter Adjustments Value Parameter 21-Operating ModeStart Control Type of ControlParameter 21-Operating Mode = 6 or Electronic Pot Control Terminal Logic3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current Value Description 0 Output Off Parameter 71-ANALOG OUTPUT SELECT2 Output Current, Full Scale = 200% of Rated Current 3 Drive Load, Full Scale = 200% of Rated LoadParameter 75-RELAY OUTPUT SELECT Value Description Level Two Parameter Adjustmentsoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation Braking Action / Function DC Braking DisabledParameter 41-Parameter 47-DC BRAKE TIME Fixed Boost Volts/Hertz Profiles100% Square 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Pull-Down Parameter 77-External Trip SelectDescription / Function Parameter 81-Factory Settings Value Description Page Parameter 82-Start Options - Continued Value Description Auto Restart is active after application of line power and RunValue Displayed Diagnostic Displays Section TroubleshootingFault Codes Fault Code Description Troubleshooting MaintenanceIndication Possible CauseIndication adjustedPossible Cause Corrective ActionIndication Ambient temperature tooPossible Cause Corrective Action4-6 Troubleshooting Illustrations Section 5 Illustrations5-2 Illustrations Illustrations 3 & 5 HP NEMA 230 & 460VAC5-4 Illustrations Parameter List Appendix A ParametersFactory Setting User SettingSetting Parameter List ± ContinuedSetting Param501 646±4711 Fax 501 648±5792 BALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400Form 1099A  Baldor Electric Company