Manuals / Baldor / Lawn and Garden / Yard Vacuum

Baldor ID101F50-E manual Electronic Pot Control Terminal Logic, Parameter 21-Operating Mode = 6 or

Models: ID101F50-E

1 74

Download 74 pages 26.37 Kb

Page 44

Electronic Pot Control Terminal Logic

Electronic Pot Control Terminal Logic

Parameter 21-Operating Mode = 6 or 7

	COMMAND		CONTROL TERMINALS
	DESCRIPTION
	DESCRIPTION	FWD	REV	PS1	PS2
	STOP	OPEN	OPEN	X	X
	Speed = 0	CLOSED	CLOSED	X	X
	FWD Decrease	CLOSED	OPEN	CLOSED	X
	FWD Hold	CLOSED	OPEN	OPEN	OPEN
	FWD Increase	CLOSED	OPEN	OPEN	CLOSED
	REV Decrease	OPEN	CLOSED	CLOSED	X
	REV Hold	OPEN	CLOSED	OPEN	OPEN
	REV Increase	OPEN	CLOSED	OPEN	CLOSED

X=Don't Care Condition.

31-Min Output Frequency - Sets a minimum output frequency provided to the motor. During operation the output frequency will not be allowed to go below the minimum output frequency unless the motor is starting from 0 Hz or is ramped to a stop. The available values are 0 to 400 Hz. The factory setting is 0 Hz.

32-Max Output Frequency - Sets a maximum output frequency provided to the motor. The available values are 20 to 400 Hz. The factory setting is 60 Hz.

42-Accel Time #1 - Sets the time in seconds for the output frequency of the inverter to linearly increase from 0 Hz to the frequency specified by parameter 32-Max Output Frequency. The adjustable range is from 0 Sec to 600 Sec.

43-Decel Time #1 - Sets the time in seconds for the output frequency of the inverter to linearly decrease from the frequency specified by parameter 32-Max Output Frequency to 0 Hz. The adjustable range is from 0 Sec to 600 Sec.

Operation 3-9

Image 44

Baldor ID101F50-E manual Electronic Pot Control Terminal Logic, Parameter 21-Operating Mode = 6 or

Contents

6/98 MN710Series Inverter Control Installation and Operating Manual AC INVERTERTable of Contents SectionTable of Contents SectionSection MOL Terminal Connections16-Load Torque Appendix A iv Table of ContentsSection SectionLimited Warranty Section General InformationSafety Notice WARNING Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury Specifications Linear to Squared Reduced in 6 patternsKeypad, 2 Wire, 3 Wire, Preset Speeds 0C to 40C Maximum without deratingFault Conditions Operator KeypadAnalog Outputs Relay OutputsRatings 1-8 General Information Section Installation Location and MountingTerminal Access Cover Removal 2-2 InstallationFigure 2-2 Terminal and Jumper Locations Wiring ConsiderationsTerminal and Jumper Locations B. Minimize voltage harmonics from the inverter to the power line Output Wire Size and Protection DevicesWire Main Circuit Wiring nameplate. Use of control with wrong powerRecommended Terminal Tightening Torques Do not use this control with any inputAC Power Connections Motor Connections 2-8 InstallationM-Contactor Figure 2-3 Typical Connections for M-ContactorLogic Wiring Analog Command InputsExternal Trip Connection Analog OutputOpto Isolated Inputs Jumper J19 Input Selection Jumper J19 SelectionsReference Selection Of Operation Mode And Connection DiagramsRelay Outputs Function 2 Wire Run/Stop ConnectionsSpeed Select Ramp Select Speed SelectFunction FunctionFunction 3 Wire Run/Stop ConnectionsSpeed Select 2 Wire Run/Stop, Electronic Potentiometer Connections 3 Wire Run/Stop, Electronic Potentiometer ConnectionsSee recommended tightening torques for terminal connectors Parameter 21 - Operating Mode =MOL Terminal Connections 77-External Trip Select Analog MeterRelay Output Pull±Down LogicJumper J19 - Used to select the active state of the opto isolated inputs Pull-Up or Pull-down Logic and to select the type of analog speed command signal to be applied. The available analog speed command signals are 0-5 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA. A 5kohm 1/2 Watt Potentiometer can be used by configuring for 0-5 VDC Check of Motors/Couplings Pre-Operation ChecksCheck of Electrical Items Temporary Application of Power Pre-Operation Check List2-22 Installation Section Operation Keypad Key FunctionsFWD Used to initiate a forward direction run of the motor OPERATING CONDITION Keypad Status IndicatorSTATUS INDICATION Description of Keypad Displays 3-4 OperationSymbol DescriptionStop Mode Run ModeProgram Mode Control Operation AdjustmentSecurity Access/Lockout Level One Parameter Adjustments Parameter 21-Operating Mode ValueStart Control Type of ControlElectronic Pot Control Terminal Logic Parameter 21-Operating Mode = 6 or3-10 Operation Value of Parameter 67 + Motor FLA X 100 03±Rated Current Parameter 71-ANALOG OUTPUT SELECT Value Description 0 Output Off2 Output Current, Full Scale = 200% of Rated Current 3 Drive Load, Full Scale = 200% of Rated LoadLevel Two Parameter Adjustments Parameter 75-RELAY OUTPUT SELECT Value Descriptionoccurrence. The elapsed time is indicated in 0.1 hour increments with 0.9 hour maximum displayed. The two left most digits displayed is the fault code and the right most digits is the elapsed time 35-Preset Speed #3 - Sets the output frequency when Preset Speed #3 is commanded at the Control Terminal Strip. The adjustable range is 0.1-400 Hz. The factory setting is 40 Hz Parameter 41-ACCEL/DECEL/COAST SELECT Value Description Operation Braking Action / Function DC Braking DisabledParameter 41-Parameter 47-DC BRAKE TIME Fixed Boost Volts/Hertz Profiles100% Square 3-20 Operation 62-Load Torque Limit REV - Sets the maximum amount of current that is supplied to the motor under a motoring reverse condition before Torque Limiting takes affect. The range of adjustment is 30- 150% of parameter 03-Rated Current. The factory setting is 150% Pull-Down Parameter 77-External Trip SelectDescription / Function Parameter 81-Factory Settings Value Description Page Auto Restart is active after application of line power and Run Parameter 82-Start Options - Continued Value DescriptionValue Displayed Section Troubleshooting Diagnostic DisplaysFault Codes Fault Code Description Maintenance TroubleshootingIndication Possible Causeadjusted IndicationPossible Cause Corrective ActionAmbient temperature too IndicationPossible Cause Corrective Action4-6 Troubleshooting Section 5 Illustrations Illustrations5-2 Illustrations 3 & 5 HP NEMA 230 & 460VAC Illustrations5-4 Illustrations Appendix A Parameters Parameter ListFactory Setting User SettingParameter List ± Continued SettingSetting ParamBALDOR ELECTRIC COMPANY P.O. Box Fort Smith, AR 72902±2400 501 646±4711 Fax 501 648±5792Form 1099A  Baldor Electric Company