Grounding Instructions
This heater is for use on 240 (or 208) volts. The cord has a plug as shown to the right. No adapter is available for this blade configuration, and none should be used. The outlet type is a 240 (or
208)volt grounding outlet. When properly installed, it provides a ground connection through the cord to the heater to protect the operator from electrical shock.
CGH402 – 20 AMP
Plug Configuration | Receptacle Configuration |
Installation Instructions
CAUTION: Heater will operate on either 240 or 208 volts. Check heater voltage and phase on label on back of heater to make sure they are the same as the electrical service supplied. See plug configurations below. Altering the cord in any way will void the warranty!
Be sure that the electrical receptacle is of the configuration and capacity appropriate for the heater. The heater may be used as a heavy duty portable. It may also be hung on the wall or ceiling using the bracket provided. The wall/ceiling mounting structure and anchoring provisions must be of sufficient strength to support the combined weight of the heater and mounting bracket.
Specifications
MODEL | WATTS | VOLTS (60 Hz) | BTUs | AMPS | PLUG TYPE |
CGH402 | 4000/3000 | 240/208 | 13,648/10,236 | 16.7/14.4 | 20 Amp |
Operation and Maintenance
How To Operate Your Heater
1.Turn the thermostat knob fully clockwise 
.
2.When the room reaches your comfort level, turn the thermostat
knob counter clockwise
until the heater shuts off. One or two minor adjustments may be necessary as the heat becomes better distributed throughout the area.
3.To reduce the room temperature, turn the knob counter clockwise
. To increase the room temperature, turn the knob clockwise
.
Maintenance
Heaters are equipped with a permanently lubricated motor and, therefore, no maintenance other than occasional cleaning is required.
WARNING WHEN CLEANING OR DISSASEMBLING HEATER, BE SURE TO DISCONNECT HEATER CIRCUIT.
To disconnect heater, turn thermostat to “OFF”, then remove plug from electrical outlet before cleaning or performing any maintenance. Allow heater to cool. IMPORTANT: Heater must be unplugged before performing any maintenance.
For dusting, use a soft cloth. For cleaning, use only a damp rag and nonabrasive dish detergent. Do not use abrasive or chemical cleaners as these may damage the finish. If heater is used in a dusty location, use a vacuum cleaner dust brush to remove dust and other foreign particles from the grill. Always unplug cord and wind it around heater handles when not using. Keep heater in a safe location for storage.
Any other servicing should be performed by an authorized service representative.
Temperature Limiting Device
All heaters are equipped with a thermally actuated manual reset limit control which automatically disconnects heating element and motor in the event normal operating temperatures are exceeded. If heater should fail to operate with thermostat turned clockwise to its limit, disconnect heater and wait a few minutes allowing heater to cool. Using a small straight object such as a pencil, push in button located inside small hole marked RESET. The thermal cutout almost invariably indicates a partial or complete blockage of the air intake or exit. Be sure to keep these areas clear in order to allow proper circulation of air.
Warranty
Maintenance: For more effective and safer operation and to prolong the life of the heater, read the Owner’s Guide and follow the maintenance instructions included with each heater. Failure to properly maintain the heater will void any warranty and may cause the heater to function improperly. Warranties are non transferable and apply to original consumer only. Warranty terms are set out below.
LIMITED
THESE WARRANTIES DO NOT APPLY:
1.Damage occurs to the product through improper installation or incorrect supply voltage;
2.Damage occurs to the product through improper maintenance, misuse, abuse, accident, or alteration;
3.The product is serviced by anyone other than Cadet;
4.If the date of manufacture of the product cannot be determined;
5.If the product is damaged during shipping through no fault of Cadet.
6.CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES SUCH AS PROPERTY DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR INCIDENTAL EXPENSES RESULTING FROM BREACH OF THESE WRITTEN WARRANTIES OR ANY EXPRESS OR IMPLIED WARRANTY.
7.IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION OF REPLACEMENT PARTS DOES NOT MODIFY OR EXTEND THE UNDERLYING WARRANTIES. REPLACEMENT OR REPAIR OF ANY CADET PRODUCT OR PART DOES NOT CREATE ANY NEW WARRANTIES.
8.These warranties give you specific legal rights, and you may also have other rights which vary from state to state. Cadet neither assumes, nor authorizes anyone to assume for it, any other obligation or liability in connection with its products other than as set out herein.
If you believe your Cadet product is defective, please, contact Cadet Manufacturing Co. at
Parts and Service
Visit http://support.cadetco.com for information on where to obtain parts and service.
©2009 Cadet Manufacturing Co. | Printed in U.S.A. Rev. 11/10 #720100 |
2
