GETTING STARTED
When the ‘Power’ button (1) is depressed the LED (2) to the left of the LCD display (3) will be red for standby mode. Pushing the LED will cause the LED to be green indicating the unit is fully powered up.
•Depressing the ‘Tape’ (4) button will cause the LCD display to show ‘Tape’.
•Depressing the ‘AM/FM’ (5) button will cause the LCD display to show ‘AM’ or ‘FM’.
•Depressing the ‘CD’ (6) button will cause the LCD display to show ‘Disc’.
DIGITAL VOLUME CONTROL
•Press ‘VOL ▼’ (7) to reduce the volume, the level will be shown in the LCD panel. Minimum volume will show ‘00’ on the LCD display.
Electronic Volume Control Display
VOL 04
Press ‘VOL ▲’ (8) to increase the volume. Maximum volume is ‘40’ on the LCD display.
TREBLE AND BASS CONTROLS
‘TREBLE ▲’ (9) and ‘TREBLE ▼’ (10) can be used to adjust the Treble up and down respectively, while ‘BASS
▲’ (11) and ‘BASS ▼’ (12) can be used to adjust the Bass up and down respectively. Both Treble and Bass can be adjusted in the range of +5 to
Treble | Bass |
tre+2 ba-1
PLL RADIO FUNCTION
•Press ‘AM/FM’ (5) to select the desired reception band. Extend the telescoping antenna (13) for FM. There is a
the LCD display.
AM Band Selection
AM 520KHz
•Press the ‘TUNER ▲’ (14) or ‘TUNER ▼’ (15) button repeatedly until the desired station shows on the LCD display.
•To automatically scan through the frequency bands, hold the ‘TUNER’ button down until you see the speed of the LCD display increase. Scanning will stop when a strong signal is detected.
Set the FUNCTION Selector to:
TAPE (4) to record from microphone. Plug mic into jack (29) or (30)
AM/FM (5) to record from radio
CD (6) to record from CD
1.Insert a blank tape into cassette Deck A.
2.Press the PAUSE button then the RECORD button on Deck A to prepare for recording. As the RECORD button is pressed the PLAY button will follow.
3.Press PAUSE again to start recording.
Dubbing (Recording from Tape B to Tape A)
1.Insert a blank tape into cassette Deck A, and the source or prerecorded tape into Deck B.
2.Press the PAUSE button then the RECORD button on Deck A to prepare for recording. As the RECORD key is pressed the PLAY button will follow.
3.Press the PLAY button on Deck B, the PAUSE button on Deck A will release automatically and
recording will begin.
Note: Every new cassette tape has erase prevention tabs. Commercially prerecorded tapes have the tabs removed to prevent recording over the original material or accidental erasure. Cover the openings with adhesive tape if you wish to record over such cassette tape.
To Stop Recording
Press the STOP/EJECT button on Deck B or press the PAUSE key on Deck A to momentarily stop recording.
Cueing with the Tape A Counter (46)
Rewind the tape to the beginning. Press the RESET button to reset the counter to (000). Use the Tape A Counter Display to note precise points on an audio tape during playback and to cue the tape to those precise points using the
Compact Disc Player Operation
The
Loading a Compact Disc
1.Lift to open the CD door and see “OPEN” on the LCD display.
2.Place a CD in compartment with label side up.
3.Press the CD door down to close.
Compact Disc Play
To play a loaded CD:
1.Turn power ON.
2.Set the FUNCTION Selector to CD.
3.The LCD will show the number of tracks and playing time.
4.Press the PLAY/PAUSE button.
The CD Display will show the current track and playing time.
6 | 11 |