Campbell Hausfeld DH4200, DH5300, DH3200, DH3800 Model Descriptions Cont, General Safety, Set Up

General Purpose Spray Guns

Modelos DH3200, DH3800, DH4200 y DH5300, IFS530

	Model Descriptions			! WARNING
	(Cont.)		Use a face mask/respirator
			and protective clothing
		• Adjusts for vertical or horizontal
			when spraying. Always
		patterns.
			spray in a well ventilated area to
	NOTE: This gun cannot be used with a
			prevent health and fire hazards. Refer
	paint tank.		to Material Safety Data Sheets (MSDS)
	MODEL DH3800		of spray material for details.
		• Comes from the factory as a pressure
		feed, non-bleeder type; convertible		! DANGER
		to bleeder type trigger actuation.	Never spray closer than 25
		• Uses external mix air cap.	feet to the compressor! If
		• Has fluid control knob.	possible, locate
		• Adjusts for vertical or horizontal	compressor in separate room. Never
		patterns.	spray into the compressor, compressor
	NOTE: This gun cannot be used with a		controls or the motor.
	paint tank.		3. Do not smoke or eat when spraying
	MODEL DH4200				paint, insecticides, or other
		• Comes from the factory as a pressure			flammable substances.
		feed, non-bleeder type; convertible
		to siphon feed, bleeder type or any		! WARNING
		combination of these types	Do not spray flammable
		• Uses internal or external mix air caps.
			materials in vicinity of
		• Has fluid control knob.
			open flame or near
		• Adjusts for vertical or horizontal
			ignition sources. Motors, electrical
		patterns.
			equipment and controls can cause
		• May be used with a paint tank.
			electrical arcs that will ignite a
	MODEL DH5300/IFS530
			flammable gas or vapor. Never store
		• Comes from the factory as a non-	flammable liquids or gases in the
		bleeder, siphon feed, external mix	vicinity of the compressor.
		gun. Can be converted to pressure	4. When spraying and cleaning, always
		feed, internal mix type.
					follow the instructions and safety
		• Switches easily from siphon to
					precautions provided by the material
		pressure feed with the twist of a
		knob.			manufacturer (Refer to MSDS).
		• Uses internal or external mix air caps.				Do not spray acids,
		• Has fluid control knob.		! WARNING		corrosive
		• Has pattern control knob.
			materials, toxic chemicals, fertilizers or
		• Adjusts for vertical or horizontal
			pesticides. Using these materials could
		patterns.
			result in death or serious injury.
		• May be used with a paint tank.
			5. Keep visitors away and NEVER allow
	General Safety				children or pets in the work area.
						Never aim or
	1. Read all manuals			!	WARNING	spray at yourself
		included with this	or anyone else or serious injury could
			occur.
		product carefully. Be
		thoroughly familiar	6. Always work in a clean environment.
		with the controls and			To avoid injury and damage to the
		the proper use of the equipment.			workpiece, do not aim the spray gun
	2. Follow all local electrical and safety				at any dust or debris.
		codes as well as in the United States,
		the National Electrical Codes (NEC),		! WARNING
		Occupational Safety and Health Act	Do not use pressure that
		(OSHA) and the Environmental	exceeds the operating
		Protection Agency (EPA).	pressure of any of the
			parts (hoses, fittings, etc.) in the
		! WARNING	painting system.
	Safety glasses and ear					Keep hose away
	protection must be worn			! CAUTION		from sharp
	during operation.		objects. Bursting air hoses may cause
			injury. Examine air hoses regularly and
			replace if damaged.
www.chpower.com

7.Always use a pressure regulator on the air supply to the spray gun.

NOTICE	Failure to install
	appropriate

water/oil removal equipment may result in damage to machinery or workpiece.

Do not misuse this

!WARNING product. Excessive exposure to vibration, work in awkward positions, and repetitive work motions can cause injury to hands and arms. Stop using any tool if discomfort, numbness, tingling, or pain occur, and consult a physician.

CALIFORNIA PROPOSITION 65

!DANGER

You can create dust when you cut, sand, drill or grind materials such as wood,

paint, metal, concrete,

cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

Set Up

USE OF AIR CAPS

Internal Mix—Generally used with slow drying, heavy bodied materials and for faster material application. NOT to be

used with fast drying paints and lacquers which will clog the opening in the air cap. INTERNAL MIX CAPS

MUST BE USED WITH PRESSURE FEED OPERATION.

External Mix—Used for quick drying, light bodied materials such as lacquers and synthetic enamels. Better for finer finish work.

THESE CAPS CAN BE USED WITH EITHER SIPHON OR PRESSURE FEED.

FAN DIRECTION

The direction of the fan (horizontal or vertical) can be changed by loosening the lock ring and turning the air cap 90 degrees (See Figure 1). Hand tighten lock ring after adjustment.

Air Cap

Horizontal Fan

Vertical Fan

Lock Ring

Figure 1

Guía de Diagnóstico de Averías
	Problema	Posible(s) Causa(s)		Acción a Tomar
El patrón de rocío es		1.	Acumulación de material	1.	Limpie la tapa de aire
muy pequeño			seco en los orificios de la tapa
			de aire
		2.	Material aglutinado	2.	Diluya o cuele el material
		3.	Insuficiente cantidad de	3.	Abra más la perilla de control de fluído
			material
		4.	Insuficiente presión de fluído	4.	Aumente la presión de aire. No exceda 3,45 bar
El patrón de rocío es		1.	El material está muy espeso	1.	Diluya el material
inadecuado		2.	La tapa de aire está sucia	2.	Límpiela
		3.	Está aplicando mucho	3.	Cierre la perilla de control de fluído para reducir el flujo de
			material		material
		4.	El patrón es muy ancho	4.	Cierre más la perilla de control de fluído o acerque más la
					pistola a la pieza de trabajo
Exceso de rocío		1.	Demasiada presión de aire	1.	Reduzca la presión de aire
			para el tipo de material que
			está aplicando
		2.	El material está muy diluído	2.	Mézclelo con material más espeso. Reduzca la presión de
					aire. Gradualmente abra la perilla de control de fluído
Fuga por la tuerca de		1.	El empaque está muy flojo	1.	Apriete la tuerca del empaque. Reemplace el empaque si no
control de fluído					puede parar la fuga al apretar la tuerca
		2.	El empaque está desgastado	2.	Reemplácela o lubríquela con aceite sinsilicón
			o reseco
Fuga por el envase y la		1.	El empaque del envase está	1.	Limpie el empaque. Reeplácelo si es necesario
tapa del envase			mal colocado
		2.	El envase no está bien	2.	Apriételo bien. Aplique una pequeña cantidad de vaselina o
			apretado		grasa mineral en las roscas cuando vaya a colocarle la tapa al
					envase
Cáscara de naranja		1.	El material se está secando	1.	Use un solvente más lento o añanda un agente retardante
(apariencia de			muy rápido
ondulación áspera		2.	Pistola muy lejos de la superficie	2.	Acerque la pistola a la superficie
semejante a una		3.	Material muy espeso	3.	Diluya el material según las instrucciones de cómo hacer
cáscara de naranja real)					menos densos los materiales
Chorreos y depresiones		1.	Material muy diluido	1.	Añada material para aumentar el espesor
		2.	La pistola se está moviendo	2.	Mueva la pistola más rápido
			muy lentamente
		3.	Flujo excesivo de material	3.	Gire la perilla de control de material en sentido horario para
					reducir el flujo
		4.	Pistola muy cerca de la superficie	4.	Aleje más la pistola de la superficie
Superficie con acabado		1.	Demasiado solvente	1.	Disminuya el solvente
moteado y tosco		2.	Técnica deficiente de rociado	2.	Refiérase a “Operación” para las instrucciones de rociado

23 Sp

2