
Operating Instructions |
|
|
|
| SB504000 | ||
Operating Instructions | 5. | Depress the Work |
| 3a. For nails, insert a stick | |||
(Continued) |
| Contact Element |
| of Campbell Hausfeld | |||
OPERATIONAL MODE - SINGLE CYCLE |
| (WCE) against the |
| nails or equivalent | |||
| work surface without |
| (see “Fasteners” | ||||
| Always know the |
|
| ||||
|
| pulling the trigger. |
| section) into the | |||
| operational mode of |
|
| ||||
the tool before using. Failure to know |
| The tool MUST NOT OPERATE. | magazine. Make sure the pointed | ||||
the operational mode could result in |
| Do not use the tool if it operates | ends of the fasteners are resting on | ||||
death or serious personal injury. |
| without pulling the trigger. Personal | the bottom ledge of the magazine | ||||
|
|
| |||||
This tool requires the trigger to be |
| injury may result. |
| when loading. Make sure the nails | |||
pulled each time a nail is driven. The | 6. Remove the tool from |
| are not dirty or damaged. | ||||
nailer can be actuated by depressing the |
| 3b. For staples, load a clip | |||||
| the work surface. |
| |||||
WCE against the work surface followed |
|
| |||||
| The Work Contact |
| of staples with the | ||||
by pulling the trigger. |
|
| |||||
| Element (WCE) must |
| crowns straddling the | ||||
|
|
|
| ||||
The trigger must be released to reset |
| return to its original |
| magazine rail. | Magazine Rail | ||
the tool before another nail can be |
| down position. The tool MUST NOT |
| ||||
|
|
| |||||
driven. |
| OPERATE. Do not use the tool if it | 4. Push the magazine | ||||
|
|
| operates while lifted from the work | cover forward |
| ||
|
|
| surface. Personal injury may result. | until latch button | |||
|
| 7. | Pull the |
| pops up. |
| |
|
|
|
|
| |||
|
|
| trigger |
| 5. Always unload all fasteners before | ||
|
|
| and |
| removing tool from service. | ||
|
|
| depress |
| Unloading is the reverse of loading, | ||
|
|
| the work |
| except that you must disconnect the | ||
WORK CONTACT ELEMENT (WCE) |
| contact |
| air supply before unloading. | |||
| element (WCE) against the work |
|
| ||||
| Check the operation |
| ADJUSTING THE FASTENER | ||||
|
| surface. The tool MUST NOT |
| ||||
| of the Work Contact |
|
| PENETRATION |
| ||
|
| OPERATE. |
|
| |||
Element (WCE) trip mechanism before |
|
| The tool is equipped with an adjustable | ||||
each use. The WCE must move freely | 8. | Depress |
| ||||
| depth of drive feature. This allows the | ||||||
without binding through its entire |
| ||||||
| the Work |
| |||||
travel distance. The WCE spring must |
|
| user to determine how deep a fastener | ||||
| Contact |
| |||||
return the WCE to its fully extended |
|
| will be driven into the work surface. | ||||
position after being depressed. Do |
| Element |
| 1. Adjust operating pressure so nails | |||
not operate the nailer if the WCE trip |
| (WCE) |
| ||||
|
| are driven consistently. Do not | |||||
mechanism is not operating properly. |
| against |
| ||||
Personal injury may occur. |
|
| exceed 120 psi. |
| |||
| the work surface. Pull the trigger. |
| |||||
1. | Disconnect the air |
| 2. To drive |
| |||
| The tool MUST OPERATE. |
|
| ||||
| supply from the tool. |
| An improperly | the nail |
| ||
|
|
| shallower, |
| |||
|
|
| functioning tool |
| |||
|
|
| turn the |
| |||
2. | Remove all fasteners | must not be used. Do not actuate the | (C) | ||||
tool unless the tool is placed firmly | wheel (C) | ||||||
| from the magazine | ||||||
|
| ||||||
| against the work piece. |
| to right to |
| |||
| (see Loading/ |
|
| ||||
|
|
|
|
| |||
|
|
|
| the extent |
| ||
| Unloading). | LOADING/UNLOADING THE NAILER |
| ||||
| desired. |
| |||||
3. | Make sure the trigger | 1. | Always disconnect the tool from the |
| |||
3. To sink a nail |
| ||||||
| and work contact |
| air supply before loading fasteners. |
| |||
|
| deeper, turn |
| ||||
| element (WCE) move | 2. | Push | Latch |
| ||
| the wheel |
| |||||
| freely up and down |
| down on | Button |
| ||
|
| (C) to left to |
| ||||
| without sticking or |
| the latch |
|
| ||
|
|
| the extent |
| |||
| binding. |
| button. |
|
| ||
|
|
| desired. |
| |||
4. | Reconnect air supply |
| Pull back |
|
| ||
|
| 4. Make sure trigger and work contact | |||||
| on the |
| |||||
| to the tool. |
|
| ||||
|
|
| element (WCE) move freely up and | ||||
|
| magazine |
| ||||
|
|
|
| ||||
|
|
|
| down without binding or sticking | |||
|
|
| cover. |
| |||
|
|
|
| after each adjustment. | |||
|
|
|
|
|
5 | www.chpower.com |