Campbell Hausfeld NB0050 Using The Nailer, Operational Modes, Recommended Hookup

70 PSI

Min.

110 PSI

Max.

Single Cycle Pin

Pin Out

Operating Instructions Model NB0050

Using The Nailer

Read this manual and understand all safety warnings and instruc- tions before operating the nailer.

LUBRICATION

This nailer requires lubrication before using the nailer for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis.

The work surface ! NOTICE can become dam-

aged by excessive lubrication. Proper lubrication is the owner’s responsibil- ity. Failure to lubricate the nailer prop- erly will dramatically shorten the life of the nailer and void your warranty.

1.	Disconnect the
	air supply from
	the nailer to
	add lubricant.

2. Turn the nailer	OIL
so the air inlet
is facing up and
put 4-to-5
drops of 30 W
non-detergent
oil into air inlet. Do not use deter-

gent oil or oil additives. Run the nail- er briefly after adding oil and wipe off excessive oil at the exhaust.

RECOMMENDED HOOKUP

The illustration below shows the recommended hookup for the nailer.

1. The air com-

pressor must be able to maintain a minimum of 70

PSI when the nailer is being

used. An inadequate air supply can cause a loss of power and inconsis- tent driving.

2. An oiler can be used to provide oil circulation through the nailer. A filter can be used to remove liquid

and solid impurities which can rust or “gum up” internal parts of the nailer.

3.Use 3/8” air hoses with a minimum working pressure of 150 PSI. Use 1/2” air hoses for 50’ run or longer. For better performance, install a 3/8” quick plug with (1/4” NPT threads) with an inside diameter of

.315 (8mm) on the nailer and a 3/8” quick coupler on the air hose.

4.Use a pressure regulator on the compressor, with an operating pres- sure of 0 - 125 PSI. A pressure regu- lator is required to control the oper- ating pressure of the nailer.

Operational Modes

The NB0050 finish nailer may be oper- ated in the “Single Cycle” or the “Bottom Trip” mode. The nailer comes delivered in the

single cycle mode. A pin when in

place in the nailer allows you to operate in the sin- gle cycle mode.

When the pin is removed, the nailer will operate in the bottom trip mode.

Always know the operational mode

of the nailer before using. Failure to know the operational mode could result in death or serious personal injury.

SINGLE CYCLE MODE

This method is rec-

ommended when precise nail place- ment is required. The single cycle pin must be installed

in the nailer. This mode requires the trigger to be pulled each time a nail is driven. The nailer can be actuated by depressing the WCE against the work surface followed by pulling the trigger. Or the nailer can be actuated by pulling the trigger and then depressing the WCE against the work surface.

The trigger must be released to reset the tool before another nail can be dri- ven.

If the tool is in bottom trip mode because the single cycle pin has previ- ously been removed, reinstall the single cycle pin to convert the tool back to sin- gle cycle mode.

BOTTOM TRIP MODE

This method is recommended when less precise nail place-

ment is required. The single cycle pin

must be removed from the nailer. Remove the pin by removing the o- ring on one end and pushing the pin out. Replace the o-rings on the pin after removing the pin from the nailer and keep the pin assembly for later use.

Bottom trip opera- tion requires the trigger to be pulled with the nailer off the work surface. Then, the

nose of the nailer is tapped against the work surface causing a nail to be dri- ven.

Recommended Hookup			Regulator
Quick	Quick	Quick Plug	Oiler
Plug	Coupler	(Optional)

Quick

Coupler (Optional)

Air
Hose	Filter

3