Campbell Hausfeld NB0050 operating instructions Operating The Nailer

Operating Instructions Model NB0050

Each time the Work Contact Element (WCE) is depressed, a nail is driven into the work surface. Care should be taken

when using this method because a nail will be driven when the WCE is depressed by any surface.

To convert the tool back to single cycle operation, reinstall the single cycle pin and attach an o-ring to each end.

Operating The Nailer

Disconnect the nailer from the air

compressor before adjusting, clearing jams, servicing, relocating, and during non-operation.

WORK CONTACT ELEMENT (WCE)

Check the opera- tion of the Work

Contact Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its entire travel distance. The WCE spring must return the WCE to its fully extend- ed position after being depressed. Do not operate the nailer if the WCE trip mechanism is not operating properly. Personal injury may occur.

1.	Disconnect the
	air supply from
	the nailer.

2. Remove all nails from the magazine (See Loading- Unloading)

3. Make sure the
trigger and
work contact
element (WCE)
move freely up
and down	Movement
without stick-
ing or binding.

4.	Reconnect air
	supply to the	CAMPBELL
		HAUSFELD
	nailer.

5.	Depress the
	work contact
	element (WCE)
	against the
	work surface
	without pulling		1
	the trigger. The nailer MUST NOT
	cycle. Do not use the nailer if it
	cycles. Personal injury could result.
6.	Hold the nailer
	clear of the
	work surface.
	The work con-
	tact element
	(WCE) should
	return to its original down position.
	Pull the trigger. The nailer MUST
	NOT cycle. Do not use the nailer if a
	cycle occurs. Personal injury could
	result.
7.	Pull the trigger
	and depress the
	work contact
	element (WCE)	1	2
	against the
	work surface.
	The nailer MUST cycle.
8.	Depress the
	work contact
	element (WCE)
	against the
	work surface.	1	2
	Pull the trigger.

The nailer MUST cycle.

LOADING/UNLOADING THE NAILER

1.Always connect the tool to the air supply before loading fasteners.

2.Press down on

the latch. Pull back on the magazine cover.

3. Insert a stick of Campbell Hausfeld nails or equivalent (See Fastener

Section)into the

magazine. Make sure the pointed ends of the nails are resting on the bottom ledge of the magazine when loading. Make sure the nails are not dirty or damaged.

4. Push the maga- zine cover for- ward until the latch catches.

5.Unloading is the reverse of load- ing, except always disconnect the air hose before proceeding.

ADJUSTING THE NAIL PENETRATION

1.Regulate the air pressure to 70 PSI at the nailer.

2.Connect the air hoses and test for penetration by driving nails into a sample piece of wood. If the nails do

not achieve the desired penetra- tion, adjust the air pressure to a higher setting until the desired pen- etration is achieved. Do not exceed 110 PSI at the nailer or durability of the nailer will be reduced.

ADJUSTING THE DIRECTION OF THE EXHAUST

The NB0050 is
equipped with an
adjustable direc-
tion exhaust
deflector. This is	Rotate
intended to allow
the user to change

the direction of the exhaust. Simply twist the deflector to any direction desired.

CLEARING A JAM FROM THE NAILER

1.Disconnect the air supply from

the nailer.

2. Remove all

nails from the magazine. Failure to do so

will cause the nails to eject from the front

when the quick clear mechanism is opened and the jam is removed.

3. Undo latch by pulling out and down. The wire latch will disen- gage from the hooks on the nose casting.

4