Operating Instructions | Model PN0090 |
|
|
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or prop- erty damage! Retain instructions for future reference.
TM
BUILT TO LAST
Air Palm Hammer
Table Of Contents
General Safety . . . . . . . . . 1 - 2
Specifications . . . . . . . . . . . . . 2
Operating The Nailer . . . .2 - 3
Troubleshooting . . . . . . . . . . 4
Warranty . . . . . . . . . . . . . . . . 4
Description
This nailer is designed for framing, decking, joist hanger installation, cross bridging, and fencing. Features include a padded leather cover for user com- fort, an offset magnetic nose for easy fastener placement, and a compact design for working in tight applica- tions.
General Safety Information
This manual contains safety, opera- tional and maintenance information.
Read this manual and understand all safety warn- ings and instructions before
MANUAL
operating the nailer. Contact your Campbell
Hausfeld representative if you have any questions.
OPERATOR’S RESPONSIBILITY:
Before operating the nailer, read and understand all safety warnings and labels. Follow the operating instruc- tions outlined in this manual.
EMPLOYER’S RESPONSIBILITY:
Distribute this instruction manual to all users before allowing use of the nailer. Ensure all operators read, understand and follow all safety warnings, labels and instructions outlined in this manual.
Danger indicates
an imminently haz-
ardous situation which, if not avoided, WILL result in death or serious injury.
●Do not use any type
of flammable gases |
|
|
|
| |
|
|
|
| ||
or oxygen as a power |
|
|
|
| |
|
|
|
| ||
source for the nailer. | O |
| CO2 | ||
Use filtered, lub- |
| ||||
|
| ||||
|
|
|
| ||
ricated, regulated |
|
|
|
|
|
|
|
|
|
| |
compressed air only. Use of a com- pressed gas instead of compressed air may cause the nailer to explode which will cause death or serious personal injury.
●Do not exceed maxi- mum operating pres- sure of the nailer
(125 psi). The nailer will not function properly. Do not use
a compressed air source capable of more than 200 PSI. The nailer could explode which will cause death or serious personal injury.
●Never use gasoline
or other flammable liquids to clean the nailer. Never use the
nailer in the presence
of flammable liquids or gases. Vapors could ignite by a spark and cause an explosion which will result in death or serious personal injury.
● Always remain in a firmly balanced position when using or handling the nailer.
Warning indicates ! WARNING a potentially haz-
ardous situation which, if not avoided, COULD result in death or serious injury.
●Always
disconnect nailer from
air line before
adjusting or servicing the nailer, or when the nailer is not in use.
●Protect your eyes and ears. Wear
Z87 safety glasses, with side shields. Wear hearing protection. Employers
Model PN0090
Locate model and serial number on tool and record below:
Model No. ________________________
Serial No. _________________________
Retain these numbers for
future reference.
and users are respon- sible for ensuring the
user or anyone near the nailer wears this safety protection.
Serious eye injury or permanent hearing loss could result.
●Never carry the nailer by the air hose or pull the hose to
move the nailer or a compressor. Keep
hoses away from
heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool dam- age could occur.
● Do not operate or
allow anyone else to operate the
nailer if any warn- 
ings or warning 
labels are not legible. 
Warnings or warning
labels are located on the nailer body.
●Do not drop or throw the tool. Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool
Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American National | IN268801AV 6/01 |
Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA |
|
© 2001 Campbell Hausfeld |
|
