Canon LV-X1 1 2 3

15

BEFORE OPERATION

Pull out Battery Holder. Replace with new battery. Install

with battery (+),(–) marks properly. Install battery and

Battery Holder into

Remote Control Unit.

BATTERY

LITHIUM BATTERY

CR2025 (3.0V)

(+) mark indicates

its (+) polarity.

Put Battery + mark

as shown direction.

BATTERY HOLDER

REMOTE CONTROL BATTERY INSTALLATION

To insure safe operation, please observe the following precautions :

●Use only specified battery. Improper battery may cause malfunction of Remote Control or improper battery's

installation may cause explosion.

●Be sure to install battery with correct polarity.

●Do not expose a battery to moisture or heat. Do not charge a battery.

●If a battery have leaked on Remote Cotrol Unit, carefully wipe the case clean and load a new battery.

●Dispose used battery according to the battery-manufacturer's instrunctions.

1 2 3

30°

30°

Point Remote Control Unit toward projector (Receiver

Window) whenever pressing any button. Maximum

operating range for Remote Control Unit is about 16.4’ (5m)

and 60°in front of the projector.

16.4’

(5 m)

OPERATING RANGE

Contents

Main CAUTION TO THE OWNER SAFETY PRECAUTIONS SAFETY INSTRUCTIONS Voor de klanten in Nederland COMPLIANCES AC POWER CORD REQUIREMENT AC Power Cord for the United States and Canada : Federal Communication Commission Notice For use in Germany TABLE OF CONTENTS FEATURES AND DESIGN 6 BEFORE OPERATION 14 COMPUTER INPUT 22 VIDEO INPUT 30 FEATURES AND DESIGN Compatibility Digital Zoom (for Computer) High Resolution Image Multi-Scan System PREPARATION NAME OF EACH PART OF PROJECTOR BACK BOTTOM FRONT SETTING-UP PROJECTOR CONNECTING AC POWER CORD For Continental Europe NOTE ON THE POWER CORD Projector side AC Outlet side POSITIONING PROJECTOR ADJUSTABLE FEET 150 100 40 2 CONNECTING PROJECTOR TERMINALS OF PROJECTOR USB CONNECTOR (Series B) AUDIO OUTPUT JACK S-VIDEO INPUT JACK CONNECTING TO COMPUTER MAC ADAPTER (Not supplied) External Audio Equipment ADB port AUDIO OUT CONNECTING TO VIDEO EQUIPMENT Terminals of the Projector Cables used for connection + BEFORE OPERATION Infrared signals transmitted from this point. OPERATION OF REMOTE CONTROL BATTERY REMOTE CONTROL BATTERY INSTALLATION 1 2 3 30 16.4 (5 m) TOP CONTROLS AND INDICATORS MENU BUTTON LAMP REPLACE INDICATOR POINT (VOLUME + / ) BUTTONS LAMP INDICATOR 4 FLOW OF ON-SCREEN MENU OPERATION OPERATING ON-SCREEN MENU MENU BAR IMAGE SELECT MENU PC SYSTEM MENU IMAGE ADJUST MENU SETTING MENU BASIC OPERATION TURNING ON PROJECTOR TURNING OFF PROJECTOR TURNING ON / OFF PROJECTOR 1 1 2 BASIC OPERATION FOCUS RING ADJUSTING SCREEN SOUND ADJUSTMENT COMPUTER INPUT SELECTING INPUT SOURCE SELECTING COMPUTER SYSTEM Auto SELECT COMPUTER SYSTEM MANUALLY COMPATIBLE COMPUTER SPECIFICATIONS PC ADJUSTMENT AUTO PC ADJUSTMENT 2 NOTE MANUAL PC ADJUSTMENT 3 PICTURE IMAGE ADJUSTMENT IMAGE LEVEL SELECT (MENU) IMAGE LEVEL SELECT (DIRECT) IMAGE LEVEL ADJUSTMENT PICTURE SCREEN ADJUSTMENT NOTE VIDEO INPUT SELECTING INPUT SOURCE Y,Pb/Cb,Pr/Cr 2 Auto SELECTING VIDEO SYSTEM VIDEO JACK OR S-VIDEO JACK Y, Pb/Cb, Pr/Cr JACKS PICTURE IMAGE ADJUSTMENT IMAGE LEVEL SELECT (MENU) IMAGE LEVEL SELECT (DIRECT) IMAGE LEVEL ADJUSTMENT PICTURE SCREEN ADJUSTMENT SETTING SETTING MENU SETTING To change the code of Projector; To change the code of the Remote Control Unit; Time left until Lamp off. APPENDIX LAMP REPLACEMENT 4 5 6 NOTE : Do not reset Lamp Replace Counter when Projection Lamp is not replaced. ORDER REPLACEMENT LAMP TROUBLESHOOTING Problem: Try these Solutions WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. Problem: Try these Solution TECHNICAL SPECIFICATIONS OPTIONAL PARTS CONFIGURATIONS OF THE TERMINALS COMPUTER INPUT TERMINAL (ANALOG) CONTROL PORT CONNECTOR USB CONNECTOR (Series B)