ELECTRICAL CONNECTIONS
Disconnect vehicle battery before making any electrical connections.
Make electrical connections with supplied terminal block plug for siren functions and spliced lead wires for light control outputs. Wiring is not supplied.
Siren Connections
Electrical connections to the siren section are made using a removable terminal block plug located on the back. A label on the unit identifies the terminal function. You should install the connector on the unit before wiring. If the unit needs service the connector can be easily removed without unwiring the connector.
The power supply of the unit must be capable of delivering peak currents up to 50 amps for adequate short circuit protection and reliable operation. The preferred source is directly at the vehicle battery. The unit is internally fused.
Attach leads by stripping 3/8", inserting into connector and clamp by tightening screw. Make sure the screw is tight and the wire can't be pulled out. Failure to adequately tighten the screw can result in improper operation or burning the connector and wire.
Wire Size and Termination - The diagram shows the minimum wire size used for each connection, along with recommended lead color. If the wire is longer than 10 ft. use the next larger wire size. Use only high quality crimp connectors for installation on the vehicle.
|
|
|
|
|
|
|
|
|
| (2) #22 AWG BLU |
|
|
|
| #22 AWG WHT (See below) | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
| Connect to output |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| jack, ter mi nals or |
|
|
| #22 AWG GRN ( See bel ow) | ||||||||
|
|
|
|
|
|
|
|
|
|
| speaker of r adi o |
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| (2) #18 AWG BRN |
|
|
|
|
|
|
|
|
|
|
|
|
| #14 AWG R ED | ||||||||
|
|
| RADIO |
|
|
|
|
|
|
|
| ||||||||||||
|
| (#16 - 2 SPKR) |
|
|
|
|
|
|
|
|
|
| Use second l ead | ||||||||||
2 - SPKR - C onnect for |
|
|
|
|
|
|
|
|
|
|
|
|
| for 2 - SPKR | |||||||||
same phase (+ to +) |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| + | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| BAT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| - | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •••• | •• |
|
|
| •••• |
|
| #14 AWG BLK | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Use second l ead |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| for 2 - SPKR |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SPKR → SPKR → POS → POS → RAD → RAD → AUX → CUT → NEG → NEG → |
|
|
| ||||||||||||||
CONNECTIONS AT REAR OF UNIT WITH
Header | |
|
Install with screw terminals face down
TB0346A | Page 5 of 12 | 05/07/05 |
