Carvin C2444U manual Limited Warranty, Service, Maintaining Your Equipment, C1644P REAR PANEL

___________

________________________

C1644P 1200w Powered Mixer C1644P REAR PANEL 1 2

CARVIN ENGINEERING DATA C844, C1644(P), C2444, C3244 4-BUS MIXER OPERATING MANUAL

C1644P REAR PANEL FEATURES:

1 & 2. SPEAKER OUTPUTS

The 1/4” JACK (1.), and TWIST-LOK JACK (2.) of each amp are wired in parallel.

The minimum load for each amp is 4 OHMS. Chaining together more than one speaker on an output is fine as long as the total impedance is not below 4 ohms. If the speaker load is lower than 4 ohms, the amp may go into one of the PROTECT modes. (Two 8 ohm speakers in parallel = 4 ohms) 12 Gauge TWIST- LOK speaker cables are an industry standard for high power applicattions (pin 1+ is POS, pin 1- is NEG, pins 2+ and 2- are not used). The 1/4” jacks are used for lower power applications. Use only 16 gauge (or heavier) speaker cables, NOT shielded instrument cables. Turn power off before connecting speaker cables.

C1644P FRONT PANEL

5

6

34

“OUT” position turns on front L/R speakers

3.AMP ROUTING switch will select between two internally routed configurations: OUT postion: AMP1-LEFT,AMP2-RIGHT,AMP3-MONITOR1,AMP4-MONITOR2

IN position: 1 amp each, for Monitors 1 thru 4.

Speaker output levels are adjusted from the Left/Right faders or Monitor 1-4 controls. The front panel GRAPHIC EQs function with the amps, depending on the front panel EQ1 and EQ2 switch settings.

4.AMP PATCH INSERT jacks offer full flexibility for mixer to amp signal routing. These jacks are T-R-S(Tip-Ring-Sleeve). Tip is the power amp input. Ring is the signal sent from the mixer determined by the AMP ROUTING switch. The limiters are post insert. Patching a compressor or equalizer between the mixer and the amp can be done by using a stereo insert cable (like Carvin’s AP1). Connect the RING signal to the INPUT of the external device, and the TIP signal from the OUTPUT of the device. Plugging in a standard 1/4” cable (mono) into the AMP PATCH INSERT jacks allows any external signal to be sent to the internal power amps.

***DO NOT USE A BALANCED CABLE***

For example, you may want to patch the GROUP outputs (1-4) into the power amps. -Plug one end of each cable into the GROUP jacks on the top panel of the mixer. -Plug the other ends of the cables into the AMP PATCH INSERT jacks.

The GROUP 1-4 faders will now control what is heard at the SPEAKER OUTPUTS.

C1644P FRONT PANEL INDICATORS:

5.AMP CLIP LEDs - The red CLIP LEDs will flash when the particular amp has reached it’s maximum output. Occasional flashing caused by bass frquencies is OK. Consistent flashing caused by higher fre- quencies may damage drivers due to excessive distortion. This will not damage the amp.

6.PROTECT LED - The yellow LED indicates the power amp system has gone into one of its protection modes. There will be no output from the amps. If the amp output has been short circuited, or overloaded by putting less than 4 ohms on the output the amp will go into protection. Check for shorted speaker cables and speaker impedance, then reset the POWER switch (off-on). If the amp has overheated, lower the volume and make sure the fan vents are not blocked. Wait for the fan to cool the amps. Normal oper- ation will return in about 1-3 minutes.

C1644P POWER AMP SPECIFICATIONS:

RMS Continuous Power:	4Ω (20-20kHz, .1%THD) 300W/amp
	8Ω (20-20kHz, .1%THD) 200W/amp
Frequency Response:	±0.5dB, 20Hz-20kHz
	±1.5dB, 10Hz-40kHz
THD: (50% output)	0.03%
Output Noise:	< -75dBu speaker out (all levels minimum)
Protection Circuits:	Soft Start, Short Circuit, No Load, SpeakerGuard , Thermal
	Shut-Off, Protect and Clip Indicators, Distortion-free Peak

LINE			LINE			LINE			LINE			LINE			LINE			LINE			PHANTOM				LINE	LINE			LINE			LINE			LINE			LINE				LINE				LINE			PHANTOM			LINE						GROUPS								EFF SW			PHONES		L
																					POWER																												POWER
																						1- 8																											9-16
MIC			MIC			MIC			MIC			MIC			MIC			MIC							MIC	MIC			MIC			MIC			MIC			MIC				MIC				MIC							MIC		1			2		3				4				TAPE OUT			R
																																																						MON 1		MON 2			MON 3			MON 4
																																																																		L			R
INSERT			INSERT			INSERT			INSERT			INSERT			INSERT			INSERT				INSERT				INSERT			INSERT			INSERT			INSERT			INSERT				INSERT				INSERT				INSERT				EFF 1			EFF 2		3L					3R				TAPE IN		MONO
																																																													RETURN
																																																																				RTN 4
1			2			3			4			5			6			7				8				9			10			11			12			13				14				15				16
0	50		0	50		0	50		0	50		0	50		0	50		0	50			0	50			0	50		0	50		0	50		0	50		0	50			0	50			0	50			0	50				+12													12+			POWER
GAIN			GAIN			GAIN			GAIN			GAIN			GAIN			GAIN				GAIN				GAIN			GAIN			GAIN			GAIN			GAIN				GAIN				GAIN				GAIN					8													8
0																										0			0			0			0			0				0				0				0					4													4	EQ 1				EQ 2
	LO CUT			LO CUT			LO CUT			LO CUT			LO CUT			LO CUT				LO CUT				LO CUT			LO CUT			LO CUT			LO CUT			LO CUT				LO CUT				LO CUT				LO CUT				LO CUT			0													0
	HI			HI			HI			HI			HI			HI				HI				HI			HI			HI			HI			HI				HI				HI				HI				HI			4													4		LEFT /			RIGHT /
-15																										-15			-15			-15			-15			-15	+15			-15	+15			-15	+15			-15	+15				8													8
	+15	1k			1k			1k			1k			1k			1k				1k				1k		+15	1k		+15	1k		+15	1k		+15	1k				1k				1k				1k				1k		–12													12-		MON 1			MON 2
FREQ			FREQ			FREQ			FREQ			FREQ			FREQ			FREQ				FREQ				FREQ			FREQ			FREQ			FREQ			FREQ				FREQ				FREQ				FREQ					c CONCERT SERIES
0	100 5k		0	100 5k		0	100 5k		0	100 5k		0	100 5k		0	100 5k		0		100	5k	0		100 5k		0	100 5k		0	100 5k		0	100 5k		0	100 5k		0		100	5k	0		100	5k	0		100	5k	0		100	5k
-15	MID		-15	MID		-15	MID		-15	MID		-15	MID		-15	MID		-15		MID		-15		MID		-15	MID		-15	MID		-15	MID		-15	MID		-15		MID		-15		MID		-15		MID		-15		MID			+12															C1644
	+15			+15			+15			+15			+15			+15			+15				+15				+15			+15			+15			+15			+15				+15				+15				+15																	12+
0			0			0			0			0			0			0				0				0			0			0			0			0				0				0				0					8													8
	LOW			LOW			LOW			LOW			LOW			LOW			LOW					LOW			LOW			LOW			LOW			LOW				LOW				LOW				LOW				LOW			4													4				PEAK
																																																							0													0
-15	+15		-15	+15		-15	+15		-15	+15		-15	+15		-15	+15		-15	+15			-15	+15			-15	+15		-15	+15		-15	+15		-15	+15		-15	+15			-15	+15			-15	+15			-15	+15				4													4				+18
																																																							8													8				+12
MON		5	MON		5	MON		5	MON		5	MON		5	MON		5	MON		5		MON			5	MON		5	MON		5	MON		5	MON		5	MON		5		MON		5		MON		5		MON		5			–12													12-
																																																																									+6
	1			1			1			1			1			1			1				1				1			1			1			1			1				1				1				1				63	125		250	500		1K	2K		4K	8K		16K						0
5	0	10	5	0	10	5	0	10	5	0	10	5	0	10	5	0	10	5		0	10	5		0	10	5	0	10	5	0	10	5	0	10	5	0	10	5		0	10	5		0	10	5		0	10	5		0	10				24-BIT DUAL STEREO EFFECTS
																																																																									- 6
	2			2			2			2			2			2				2				2			2			2			2			2				2				2				2				2			PK		5	EFFECTS 1					R	B									-12
0			0			0			0			0			0			0	10			0	10			0			0			0			0			0	10			0	10			0	10			0	10					4		6	3 OFF 3			EV E				4	5	6 7
	10	5		10	5		10	5		10	5		10	5		10	5			5					5		10	5		10	5		10	5		10	5			5				5				5				5			3			7	6		6	R				3		8					-18
																																																							2			8	9		9			A									-24
	3			3			3			3			3			3			3				3				3			3			3			3			3				3				3				3				1			9						GN		2		9
																																																							MUTE	0		10	MON 1		MON 2			E		1		10					-30
5	0	10	5	0	10	5	0	10	5	0	10	5	0	10	5	0	10	5		0	10	5		0	10	5	0	10	5	0	10	5	0	10	5	0	10	5		0	10	5		0	10	5		0	10	5		0	10		PK		5	EFFECTS 2					R	B									dB
																																																								4		6	3 OFF 3			EV E				4	5	6 7			L		R
	4			4			4			4			4			4				4				4			4			4			4			4				4				4				4				4			3			7	6		6	R		LA		3		8
																																																							2			8	9		9
0	10	5	0	10	5	0	10	5	0	10	5	0	10	5	0	10	5	0	10	5		0	10		5	0	10	5	0	10	5	0	10	5	0	10	5	0	10	5		0	10	5		0	10	5		0	10	5			1	0		9						GN		2		9
	1			1			1			1			1			1			1				1				1			1			1			1			1				1				1				1				MUTE			10	MON 1		MON 3			E		1		10
																																																							RETURN				TO MONITORS			SELECT				PARAMETER
EFF 0		10	EFF 0		10	EFF 0		10	EFF 0		10	EFF 0		10	EFF 0		10	EFF		0	10	EFF		0	10	EFF 0		10	EFF 0		10	EFF 0		10	EFF 0		10	EFF		0	10	EFF		0	10	EFF		0	10	EFF		0	10		SELECT			ECHO		REVERB				CHORUS		FLANGE
5	2		5	2		5	2		5	2		5	2		5	2		5		2		5		2		5	2		5	2		5	2		5	2		5		2		5		2		5		2		5		2						REGEN		DAMPING				REV LEVEL SPEED
																																																							PARAMETER			TIME		DECAY				DEPTH		DEPTH
0	10		0	10		0	10		0	10		0	10		0	10		0	10			0	10			0	10		0	10		0	10		0	10		0	10			0	10			0	10			0	10
	C	PAN		C	PAN		C	PAN		C	PAN		C	PAN		C	PAN		C	PAN			C	PAN			C	PAN		C	PAN		C	PAN		C	PAN		C	PAN			C	PAN			C	PAN			C	PAN			RETURN		TAPE IN							MONITORS									MONO
																																																							5			5			5			5		5			5				5
L R			L R			L R			L R			L R			L R				L R				L R			L R			L R				L R			L R			L R				L R			L R				L R					0 10			0 10		0 10			0 10			0 10			0 10				0 10
1	SIG		2	SIG		3	SIG		4	SIG		5	SIG		6	SIG		7		SIG		8		SIG		9	SIG			SIG			SIG			SIG				SIG				SIG				SIG				SIG			RTN 3			RTN 4	MON 1				MON 2			MON 3			MON 4
	PEAK			PEAK			PEAK			PEAK			PEAK			PEAK			PEAK				PEAK				PEAK		10 PEAK			11 PEAK			12 PEAK			13 PEAK				14 PEAK				15 PEAK				16 PEAK
+12		MUTE +12			MUTE +12			MUTE +12			MUTE +12			MUTE +12			MUTE +12			MUTE +12					MUTE	+12		MUTE +12			MUTE +12			MUTE +12			MUTE +12			MUTE +12				MUTE +12				MUTE +12				MUTE		+12	LEFT 12				LEFT 12			LEFT 12				LEFT			+12				PFL
																																																																									PHONES
+6		PFL	+6		PFL	+6		PFL	+6		PFL	+6		PFL	+6		PFL	+6			PFL	+6			PFL	+6		PFL	+6		PFL	+6		PFL	+6		PFL	+6			PFL	+6			PFL	+6			PFL	+6			PFL		RIGHT				RIGHT			RIGHT				RIGHT							5
																																																						+6			6			6				6					+6
0		1-2	0		1-2	0		1-2	0		1-2	0		1-2	0		1-2	0			1-2	0			1-2	0		1-2	0		1-2	0		1-2	0		1-2	0			1-2	0			1-2	0			1-2	0			1-2	0	PFL		0		PFL	0		PFL 0				PFL			0				0 10
-6		3-4	-6		3-4	-6		3-4	-6		3-4	-6		3-4	-6		3-4	-6			3-4	-6			3-4	-6		3-4	-6		3-4	-6		3-4	-6		3-4	-6			3-4	-6			3-4	-6			3-4	-6			3-4																			L-R
-12			-12			-12			-12			-12			-12			-12				-12				-12			-12			-12			-12			-12				-12				-12				-12				-12		-12			-12				-12						-12
																																																																							MONO
-24		L-R -24			L-R -24			L-R -24			L-R -24			L-R -24			L-R -24				L-R -24				L-R	-24		L-R -24			L-R -24			L-R -24			L-R -24				L-R -24				L-R -24				L-R -24				L-R	-24		-24			-24				-24						-24			MON
-30		1	-30		2	-30		3	-30		4	-30		5	-30		6	-30		7		-30			8	-30		9	-30	10		-30	11		-30	12		-30		13		-30		14		-30		15		-30		16		-30		-30			-30				-30						-30			1-2
-50			-50			-50			-50			-50			-50			-50				-50				-50			-50			-50			-50			-50				-50				-50				-50				-50		-50			-50				-50						-50			3-4
																																																																								MON

METERS

1 2 3 4 L R

C1644

CONCERT 44 SERIES The C844, C1644(P), C2444 and C3244 feature 8 to 32 channels with true 4- bus performance. The C1644P adds four 300 watt power amplifiers built into our ROAD WARRIOR case. Never before have so many features been packed into such a rugged, compact USA made mixer. The best feature of the Concert 44 Series is the sound. Sound that is pure and quiet enough for digital recording studios. Everything is logically laid out making the powerful features simple to use. The knobs have been located so that adjust- ments can be made quick and easy with visible pointers showing you the status of your mix at a glance.

TRUE 4-BUS DESIGN The Concert 44 Series offers increased mixing flexibility over standard stereo con- soles by letting you assign channels to one of the 4 sub groups or L/R. This allows you to mix the entire drum, horn, choir, etc. into one sub group, which feeds the L/R faders. This is an easy way to control the volume of grouped mics and inputs. If you don’t need subgrouping, you can depress the L/R channel button and the channel goes directly into the L/R output like a standard stereo console. All 4 sub group outputs have bal- anced outputs for long cable runs.

TWO EFFECT SENDS / TWO 24-BIT EFFECT PROCESSORS Two built-in24-Bit effects, each offering 256 stereo effects, is a first in a 4-bus mixing console. Since there are two, you no longer have to choose between that great vocal reverb with delay and that awesome guitar chorus - you can have both! Each processor offers lush REVERBS, rich CHORUSES, thick textured FLANGING and pristine ECHOES with fully adjustable parame- ters for damping, decay, depth, speed, time and regeneration. Both processors can be sent back into the moni- tor mix so the performers can hear exactly what the audience is hearing.

FOUR MONITOR SENDS Every channel has 4 MONITOR sends with MASTER output level controls. Monitor

send jacks are balanced TRS.

3 BAND EQ/MID SWEEP The superb EQ system gives extended 15 dB boost and cut tone shaping. The LOW frequency control builds bass starting with 20 Hz through 80 Hz for a solid non-flabbylow-end. The exclu- sive offset of the MID FREQ. control ends the confusion of selecting your mid frequency from 100 Hz to 5kHz. The MID cut and boost control adjusts the gain to the perfect mid-dip or boost curve to enhance all instruments and vocals. The 11.5k Hz HI treble control adds sparkle to your top-end without adding harshness. Both the LOW and HI are “shelving”, which means they are effective from 20 Hz and up to 20k Hz. The LO CUT switch eliminates stage rumble or other unwanted low frequencies that would normally rob power from your woofers.

CHANNEL FEATURES Every channel has a full balanced XLR and LINE (1/4”) preamp with an INSERT jack for a compressor or EQ that also serves as a DIRECT OUT when plugged half way. The PAN con- trol directs the channel into the L/R output or any of the 4 sub groups after depressing the appropriate ASSIGN switches. A PFL (pre fader listen) switch allows you to hear the channel in the headphones before the fader is turned up. A solid “on” condition of the PEAK LED indicates that the MUTE switch has been activated which turns the channel off including all monitor and effect sends. When flashing during use, the PEAK LED also lets you know when to adjust the channel’s GAIN control to prevent chan- nel cliping. The SIGNAL LED lets you know that a signal is coming through the channel starting at –20 dBu. A silky smooth 60mm audio taper FADER delivers professional fade-outs. The PHANTOM power switches provide power through the XLR connectors for use with condenser mics like the Carvin CM90E in groups of 8 channels.

MASTER FEATURES Each of the 4 SUB GROUP faders can be switched to the R/L outputs or used independently through their own balanced output jacks. Each of the sub group’s PFL switches allow you to listen to the sub groups in your headphones before it is turned up. The R/L MAIN output faders are independent for added flexibility over a single stereo fader. A MONO control sums both the R/L outputs together (pre-graphic EQ) for a center, side fill or subwoofer output. The stereo HEADPHONE control tracks the METER switches which allow you to look and listen from the L/R, MONO, MONITOR 1/2 and 3/4 outputs and channel PFL switches. The master section also features 2 EFFECT SENDS, 4 RETURNS and RCA TAPE IN/OUT jacks. All 4 SUB GROUPS, 4 MONITORS, XLR L/R and MONO outputs are bal- anced. A FOOT SWITCH jack turns both effects processors on or off remotely with the optional FS22 foot switch.

SWITCHING POWER SUPPLY Our exclusive 125k Hz switching power supply eliminates trans- former noise. Like a laptop computer, go anywhere in the world and not worry about power because you can run on any voltage from 90 to 250VAC. (except C1644P)

SUPERB SOUND State-of-the-art low impedance, low noise preamps are featured on every channel. The balanced common mode rejection is better than 70 dB to eliminate cable noise. All main outputs are balanced to guard against system noise. The near theoretical limit on distortion has been achieved with THD below .01% to guarantee the purity of your sound, ensuring it will be dynamically open and transparent.

ENGINEERED TO LAST Hidden deep in the heart of these San Diego, CA made mixers is the SMT con- struction that utilizes surface mounted components to prevent malfunctions caused by vibrations. Sealed controls and switches guard against the outside elements while heavy-duty jacks provide a positive con- nection to your cables. Fire retardant FR-4 military spec circuit cards feature double-sided copper to elim- inate radio frequency interference. Precision 1% tolerance components guarantee your settings will be accurate every time. The Concert 44 Series is built to strict standards.

RECEIVING INSPECTION—read before getting started

INSPECT YOUR MIXER FOR DAMAGE which may have occurred during shipping. If damage is found, please notify the shipping company and CARVIN immediately.

SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit, always use the original carton and packing material. This will provide the best possible protection during shipment. CARVIN and the shipping company are not liable for damage caused by improper packing.

SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.

SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately. Please allow several days for the rest of your order to arrive before inquiring.

RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual for your records. Keep your portion of the card and return the portion with your name and comments to us.

USA customers register online at: www.carvin.com/registration

All other countries register online at: www.carvinworld.com/registration

	Limiters.
Maximum Gain:	Mic in to Speaker Out: 74dB
Power Requirements:	120VAC 60Hz or optional 240VAC 50Hz model, 1200VA
Size:	24”W x 16”D x 9”H
Weight:	38 lbs.

TWO 9 BAND EQUALIZERS Precision equalizers provide 1 octave adjustments to tune in your overall sound and control feedback. Unlike one stereo equalizer, two independent 9 bands offers total flexibility. With two convenient buttons, you can assign either EQ to the R/L outputs or to the 1/2 monitor outputs. Center frequencies are 63, 125, 250, 500, 1k, 2k, 4k, 8k & 16k Hz.

C1644 BLOCK DIAGRAM

CONCERT 44 SPECIFICATIONS:For C1644Ppower amp specifcations, see back page

Mic Input:	Balanced XLR, Mic Imp. 150Ω
Line Input:	Balanced 1/4” Jack Imp. 10k/20k bal.
Frequency Response:	Mic or Line Inputs: 20Hz-20KHz ±0.5dB
Total Harmonic Distortion:	Less than .01%

	This symbol is intended to alert the user		This symbol is intended to alert the
		CAUTION
	to the presence of uninsulated “dangerous		user to the presence of important
	voltage” within the product’s enclosure that		operating and maintenance (servic-
	may be of sufficient magnitude to consti-	RISK OF ELECTRIC SHOCK	ing) instructions in the literature
tute a risk of electric shock to persons.		DO NOT OPEN	accompanying the appliance.

IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:

WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polariza- tion means of an appliance is not defeated.

POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

SERVICING: The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse. Refer to replacement text on the unit for correct fuse type.

SAFETY INSTRUCTIONS (EUROPEAN)

The conductors in the AC power cord are colored in accordance with the following code.

GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live

U.K. MAIN PLUG WARNING: Amolded main plug that has been cut off from the cord is unsafe. NEVER

UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAIN PLUG INTO A POWER SOCKET.

LIMITED WARRANTY

Your Carvin mixer is guaranteed against failure for 1 YEAR unless otherwise stated. Carvin will service and supply all parts at no charge to the customer providing the unit is under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes no responsibility for horn drivers or speakers dam- aged by this unit. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions. This warranty is in lieu of all other warranties, expressed or implied. No representative or person is authorized to represent or assume for Carvin any liability in connec- tion with the sale or servicing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDEN-

TAL OR CONSEQUENTIAL DAMAGES.

SERVICE:

In the USA go to www.carvin.com/cs

Outside the USA, contact your dealer or go to http://www.carvinworld.com for your nearest

service center. Include a written description of the problem with serial number and date of pur- chase.

MAINTAINING YOUR EQUIPMENT

Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel of your unit can be wiped from time to time with a dry or slightly damp cloth in order to remove

dust and bring back the new look. As with all pro gear, avoid prolonged use in caustic environments such as dust or salt air. When used in such an environment, be sure the mixer is adequately protected by a cover.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL!

INSERT￿

￿PEAK ￿SIG ￿PFL

PFL￿ LEFT￿ RIGHT￿ GROUP1￿ GROUP2￿ GROUP3￿ GROUP4￿ MON1￿ MON2￿ MON3￿ MON4￿ EFF1￿ EFF2￿

￿SWITCHES

￿PHONES

HEADPHONE ￿

CHANNELS￿

AND ￿METER

￿LEVEL

￿ASSIGN

￿PHONES

MIC￿

￿MUTE

PAN￿

L - ￿R

￿OUTPUT

￿METERS

MIC￿

LO￿

THREE BAND ￿

PRE￿

CUT￿

CHANNEL TONE ￿

CONTROLS￿

￿LINE ￿PAD

line ￿pad

￿CHANNEL

EFF ￿1

SWITCH ￿TO

￿FADER

L - R

LEFT & ￿RIGHT

(-￿16dB) ￿GAIN

￿REQ

GRAPHIC ￿EQ

￿ƒ

EFF ￿2

￿FADERS

BAL ￿OUT

￿HI

￿LOW

￿LEFT

TAPE ￿OUT

￿RIGHT

￿MID

MON ￿1

MON ￿2

￿LEFT

￿MONO

￿MONO

BAL ￿OUT

MUTE￿

MON 3￿

MON ￿4

￿RIGHT

￿PFL

GROUPS 1 - ￿4

LEFT￿

￿FADERS

BAL ￿TRS

1 - 4

EFFECTS ￿RETURN

3L - ￿3R

￿RIGHT

SWITCH ￿TO

MON 1 - ￿4

MON 1 - ￿4

GRAPHIC ￿EQ

BAL TRS￿

RETURN ￿3

LEVEL￿

MON 1 & 2 ￿ONLY

￿LEVEL

￿LEFT

EFF ￿SNDS

IN 1

DSP x 2￿

1 & ￿2

EFFECTS ￿RETURN

TAPE IN￿

4L - ￿4R

￿LEFT

IN 2

￿STEREO

RCA￿

￿TO

￿RIGHT

L & ￿R

￿TO

MONS 1 - ￿3

￿RIGHT

TAPE ￿IN

PFL￿ LEFT￿

RIGHT￿ 1GROUP￿ 2GROUP￿ 3GROUP￿ 4GROUP￿ 1MON￿ 2MON￿

3MON￿ 4MON￿

1EFF￿ 2EFF￿

RTN ￿4

LEVEL￿

Equivalent Input Noise:	150 ohm source: -117dBu
Output Noise:	less than -90dBu Master Line Out
Output Headroom:	+28dB XLR bal, +20dB 1/4” unbal.
Maximum Gain:	Mic in to Master Line Out: 74dB
Crosstalk:	Adjacent channels: -60db at 1KHz
Common Mode Rejection:	-75db at 1KHz
Phantom Power:	All XLR Mic in (channel groups of 8)
Channel EQ.:	3 band active,LOW: 80Hz ±15dB
	MID: 100Hz to 5kHz ±15dB
	HI: 11.5KHz ±15dB
9 Band Graphic EQ.:	±12dB 63, 125, 250, 500, 1k, 2k, 4k, 16k
Mixers Only:	90 to 250VAC 50-60Hz, 20 to 50VA
Powered C1644P:	120VAC 60Hz or 240VAC 50Hz model,
	1200VA
Size:	C844: 14.25”D x 14.5”W x 3.25”H
	C1644: 14.25”D x 22.25”W x 3.25”H
	C1644P: 16”D x 24”W x 9”H
	C2444: 14.25”D x 30”W x 3.25”H
	C3244: 14.25”D x 38.1”W x 3.25”H

Optional Accessories:
C844:	CB800 Heavy padded bag	FS22 foot switch for all models
C1644:	CB1600 Heavy padded bag	RW1644 Road Warrior™ case
C2444:	CB2400 Heavy padded bag	RW2444 Road Warrior™ case
C3244:		RW3244 Road Warrior™ case

InvoiceDate.No Serial following: the record to wish may you records, your For 1008 02444D-76