Carvin manual LC24 Rear Connections

2

3

4

5

6

7

1 31 30 29

28

27

26

25

24

23

22

21

20

19

18

8 9 10 11 12 13 14 15 16 17

released the scene program is locked so that chase speed and other programs can be set to new chase speeds. To return a Scene program’s chase speed control to the speed fader, place the Speed fader in the bottom SHOW MODE position. Press and hold the REC SPEED button along with the Scene programs FLASH button upon release of both buttons the control is restored.

26.) DARK BUTTON

The DARK button is like a momentary version of the BLACKOUT button. Except the DARK button cannot be over ridden by any other button while still pressed.

27.) ALL REV BUTTON / EDIT

The ALL REV button works in the Scenes mode. It reverses the direction of the chase for all scene programs running whether or not a chase speed was set using the Rec Speed button. In record Mode and in Scene mode the alternate Edit function pressed in conjunction with a scene flash button puts the console in the edit mode of that scene program. See Record Mode.

28.) % OR 0-255 / INSERT BUTTON

The % OR 0-255button is used to change the dimmer read- out on the LED display from 0-100%to 0-255steps. This is only a display reading preference. The function toggles every time the RECORD and "% OR 0-255" buttons are press and the same time. The alternate Insert function works in the record Edit mode. It is used to insert a new step into an existing program.

29.) REV ONE / DELETE BUTTON

The REV ONE button reverses the scene program who’s FLASH button is pressed at the same time. The alternate Delete function works in the record Edit mode. It is used to delete a new step into an existing program.

30.) CHASE REV / UP BUTTON

The CHASE REV button works in the Scene mode and

reverses the chase direction of the any programs running to a chase speed it will not rev scene programs that have their chase speed set by using the REC SPEED button. The UP function works in the record Edit mode. It is used to change the dimmer intensity in an existing program. In the record Edit mode, a steps dimmer intensity value is changed by pressing and holding the UP button, then as the FLASH button under the channel to be modified is pressed the inten- sity is increased. The alternate Chase Rev function works in the Scene mode and reverses the chase direction of the any programs running to a chase speed it will not rev scene programs that have their chase speed set by using the REC SPEED button.

31.) BEAT REV / DOWN BUTTON

The BEAT REV button works in the Scene mode with scene programs that have their chase speed set by the REC SPEED button and are now running with other programs with audio chase activated. The Set Speed chase programs will reverse on the next beat (may have to hold the button for two beats) after the button is released.

The alternate Down function works in the record Edit mode. It is used to change the dimmer intensity value of a step in an existing program. In the record Edit mode, a step’s dimmer intensity value is change by pressing and holding the Down button, then as the Flash button under the channel to be mod- ified is pressed the intensity is decreased.

LC24 REAR CONNECTIONS

REAR PANEL CONTROLS:

32.) POWER INPUT JACK

Use supplied AC wall adapter.

33.) MIDI THRU

Use for serial connections of more MIDI devices connected after the LC24. Has same MIDI information as going into the MIDI in jack.

34.) MIDI OUT

Use for send out MIDI information from the LC24.

35.) MIDI IN

Used for receiving MIDI information into the LC24.

36.) DMX OUTPUT

Used for send information to Dimmer packs etc.. in the DMX- 512 format.

37.) DMX POLARITY SELECT

Reverses the polarity of the balanced DMX lines. Used if Dimmer packs etc.. used with the LC24 only conform to a certain polarity. See Dimmer pack and other peripherals for correct polarity. The polarity will not damage peripherals, but they may not function properly with an incorrect setting.

38.) THE AUDIO INPUT

The audio input jack when used turns off the internal micro- phone. I can handle from 100mV to 1V pp and is controlled by the audio fader. This jack is used to control the chase rate of a scene program with an audio source.

39.) REMOTE CONTROL INPUT:

The stereo (TRS) 1/4" jack is used to remotely control the Full On and Black Out features of the console. The tip is the Full On control. It works in either momentary hold or push on push off. The Ring is the Black Out control and works as push on / push off. This is the same are these switches work

on the front console.

32 33 34 35 36 37 38 39