STOPWATCH
Using the Stopwatch Mode
The following procedure describes how to enter the Stopwatch Mode from the countdown timer.
To enter the Stopwatch Mode
1.Press D to enter the Countdown Timer/Stopwatch Mode.
2.Hold down A until the time setting starts to flash, which indicates the setting screen.
•This causes the indicator to appear on the display.
3.Use E(+) and
•Note that you cannot enter the Stopwatch Mode while the countdown timer start time is any other value besides 0'00".
4.After making the setting you want, press A to exit the setting screen.
•This causes the indicator to appear on the display, indicating the Stopwatch Mode.
•See “Moon Phase Indicator” for information about the Moon phase indicator and “Tide Graph” for information about the tide graph.
To view the Moon age for a particular date
1.In the Moon/Tide Mode, press C to display the Moon Age Screen.
2.Use E (+) and B
| Moon phase |
About one | indicator |
second |
|
later |
|
▲ |
|
Moon age
Date (Year Month – Day)
• | You can select a date in the range of January 1, 2000 to December 31, |
• | 2039. |
About one second after you display a date, its Moon age and Moon |
Minutes
HoursSeconds
•The stopwatch lets you measure elapsed time, split times, and two finishes.
•The display range of the stopwatch is 99 hours 59 minutes 59 seconds.
•The stopwatch measurement operation continues to run, restarting from zero after it reaches its limit, until you stop it.
•The stopwatch measurement operation continues even if you exit the Stopwatch Mode.
phase will appear on the display. |
To view tide data for a particular time
1. Use the steps under “To view the Moon age for a particular date” to specify the date whose data you want to view.
2. Press C to display the Tide Data Screen.
3. Use E (+) and B
whose tide data you want to view. | |
• | You can change the time in |
• | increments. |
|
To measure times with the stopwatch
Elapsed Time
EE E E A*
Start Stop Re-start Stop Clear
Split Time
E |
| A |
|
| A |
| E |
| A* |
|
| ||||||||
|
|
|
|
| |||||
Start | Split | Split release | Stop | Clear | |||||
Two Finishes |
|
|
|
|
|
|
Tide data time | When setting the tide data time using the |
| correctly as a.m. (no indicator) or p.m. (P |
| indicator). |
| • The area of the tide graph that |
| corresponds to the specified date and |
| time flashes. |
ALARM
E |
| A |
|
| E |
|
| A |
| A* |
|
|
| ||||||||
|
|
|
|
|
| |||||
Start | Split | Stop | Split release | Clear | ||||||
|
| First runner | Second runner finishes. | Display time of |
| |||||
|
| finishes. |
|
|
| second runner. |
| |||
|
| Display time |
|
|
|
|
|
|
|
of first runner.
*Pressing A here normally clears the stopwatch to all zeros. In the case of a stopwatch operation started automatically by repeat timing when the end of a countdown is reached, however, pressing A here displays the start time instead of clearing the stopwatch to all zeros.
Alarm on indicator
Alarm number Timekeeping Mode time
Alarm Time (Hour : Minutes)
You can set five independent Daily Alarms. When an alarm is turned on, the alarm tone sounds when the alarm time is reached. You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour.
•The alarm number (1 through 5) indicates
an alarm screen. appears in place of
when the Hourly Time Signal screen is shown.
•All of the operations in this section are performed in the Alarm Mode, which you enter by pressing D.
MOON/TIDE MODE
You can use the Moon/Tide Mode to view the Moon age for the current date and the Moon age, Moon phase, and tidal movements for a particular date.
Important!
Especially when you plan to view the Moon age or tide graph, be sure to specify the city data as well as the current time/date.
To display Moon and tide data
1.Press D to enter the Moon/Tide Mode.
•The initial date and Moon age are those based on the time, date, and city code you have set in the Timekeeping Mode.
2.Press C to toggle between the Moon Age Screen and the Tide Data Screen.
Moon phase indicator | Tide Graph |
|
| Press C. | |
Moon | ▲ | ▲ |
|
| |
Age |
|
|
| Date (Year Month – Day) | Tide data time |
| Moon Age Screen | Tide Data Screen |
•The initial time setting when you display the Tide Data Screen from the Moon Age Screen is always 6:00 (AM).
•The Tide Data Screen shows the Moon phase for the current date, with the area of the tide graph that corresponds to the specified date and time flashing.
To set an alarm time
1. In the Alarm Mode, use E and B to select the alarm whose time you want to set.
Press E. |
|
|
| Press B. |
|
|
AL-1 AL-2 AL-3
SIG AL-5 AL-4
2.Hold down A until the hour digits of the alarm time start to flash, which indicates the setting screen.
•This automatically turns on the alarm.
3.Press D to move the flashing between the hour and minutes.
4.While a setting is flashing, use E (+) and B
•When setting the alarm time using the
5.Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 20 seconds (in all modes), or until you stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.