USER’S GUIDE 2471
•Pressing E and B at the same time returns to OFF(no reference altitude), so the watch performs air pressure to altitude conversions based on preset data only.
3.Press A to exit the setting screen.
About the Altitude Alarm
The altitude alarm sounds for about five seconds when the current altitude matches a preset value during an altitude measurement operation. You can press any button to stop the alarm after it starts to sound.
The altitude alarm sounds only while the Altimeter Mode’s Altitude Screen is on the display. It does not sound while the watch is in another mode or while another Altimeter Mode screen is on the display.
Example
If you set the altitude alarm at 130 meters, it sounds when you pass the 130- meter mark on your way up and on your way back down.
To set the altitude alarm
|
|
|
| 1. In the Altimeter Mode, hold down A until the | |
| l ll | display clears. After four or five seconds, | |||
l | either OFF or the current reference altitude | ||||
| l | ||||
l |
| l |
| ||
l |
| value (if set) starts to flash, which indicates | |||
l |
| l | |||
l | l | l |
| ||
ll |
| the setting screen. | |||
|
|
Start Time Data | Measurement | End Time | ||
|
|
| Data | Data |
|
| Press E. |
| ▲ |
|
| ▲ |
| |
▲ | ▲ |
|
|
|
Press |
|
|
|
|
C. |
|
|
|
|
▲ |
|
|
| ▲ |
Cumulative |
| Maximum Altitude | Total Ascent | Relative Altitude |
Total Ascent |
|
|
|
|
|
| ▲ | ▲ |
Measurement Time
Alarm
|
|
| 2. Press D once to move the flashing to the | ||||
Altitude alarm value | altitude alarm setting. |
| |||||
• Press D to move the flashing in the | |||||||
|
|
| |||||
|
|
|
| sequence shown below. |
| ||
Altitude |
| Long/Short | Altitude | Reference | |||
Alarm |
|
| Mode Setting | Unit | Altitude | ||
|
|
| 3. Press E (+) or B | ||||
l | l ll | altitude alarm value by 5 meters (or 20 feet). | |||||
• | You can set the altitude alarm value within | ||||||
| l | ||||||
l |
| l | |||||
l |
|
| |||||
l |
| l |
| the range of | |||
l | l |
| |||||
| ll | l |
|
| |||
|
|
|
| ||||
|
|
|
|
|
• Pressing Eand Bat the same time resets the altitude alarm value to O.
4. Press A to exit the setting screen.
To turn the altitude alarm on and off
Hourly time signal on indicator
Alarm on indicator
Timekeeping Mode time
Alarm time (Hour : Minutes)
To set the alarm time
ll l |
After you set (and turn on) the daily alarm, the alarm tone sounds when the alarm time is reached. You can also turn on an Hourly Time Signal that causes the watch to beep for about one second every hour on the hour.
•All of the operations in this section are
performed in the Alarm Mode, which you enter by pressing D.
1. In the Alarm Mode, hold down A until the |
hour setting of the alarm time starts to flash, |
which indicates the setting screen. |
Altitude alarm on indicator
1. In the Altimeter Mode, hold down A until the |
display clears. After four or five seconds, |
either OFF or the current reference altitude |
value (if set) starts to flash, which indicates |
l |
| l | |
| l | ||
l |
| l | |
l |
| l | |
l |
| l | |
l | |||
l | |||
| ll l |
• This automatically turns on the alarm. |
2. Press D to move the flashing between the |
hour and minute settings. |
Current On/Off status
| the setting screen. |
2. | Press D once to move the flashing to the |
| altitude alarm setting. |
3. | Press C to toggle the altitude alarm on (ON) |
| and off (OFF). |
4. | Press A to exit the setting screen. |
•An altitude alarm on indicator appears on the Altimeter Mode’s Altitude Screen while the altitude alarm is turned on. This indicator does not appear on any other screen or in any other mode.
3.While a setting is flashing, use E to increase it.
•When setting the alarm time using the
4.Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds (in all modes), or until you stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down E to sound the alarm.
Data Recall
Use the Data Recall Mode to view memory measurement data.
To view memory measurement data
1.Enter the Data Recall Mode.
2.Press E to cycle through the various data screens in the sequence
shown below.
•To view the cumulative total ascent value, press C.
•If an error occurs during memory measurement, the xxxxx is shown for the relative altitude in the Data Recall Mode.
Altitude | Alternates at |
▲ | ▲ |
To turn the daily alarm and the Hourly Time Signal on and off
In the Alarm Mode, press E to cycle through the settings shown below.
Alarm On Indicator / Hourly Time Signal On Indicator
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Alarm On |
|
| Alarm Off |
|
| Alarm On |
|
| Alarm Off | |
|
| Signal On |
|
| Signal Off |
|
| Signal Off |
|
| Signal On | |
|
|
|
|
|
|
|
|
|
|
|
|
|
•The alarm on indicator and the Hourly Time Signal on indicator are shown on the display in all modes while these functions are turned on.
Backlight
The backlight uses an EL |
Recording time (Hour : Minutes)
Recording date (Year, Month – Day)
Auto light switch on | panel that causes the entire display to glow for |
indicator | easy reading in the dark. The watch’s auto light |
| |
| switch automatically turns on the backlight when |
| you angle the watch towards your face. |
| • The auto light switch must be turned on |
| (indicated by the auto light switch on indicator) |
| for it to operate. |
•See “Backlight Precautions” for other important
information about using the backlight.
4