Operation Guide 2696/2832(B)

Alarm Mode

❚To set an alarm time

Example: To set Alarm 2 for 3:30 p.m.

3. Use the D (+) and B(–) buttons to change the hour setting.

(Back)

Your watch comes with five alarms and an hourly time signal.

• Daily Alarms (AL 1 to AL 4)

 

The watch beeps for about 10 seconds when an alarm time is

 

reached.

•

Snooze Alarm (SNZ)

 

With the snooze alarm, the watch beeps for 10 seconds when the

 

alarm time is reached, and up to seven times at five-minute

 

intervals thereafter (approximately 30 minutes total). Pressing any

 

button stops the beeper, but the alarm will sound again after five

 

minutes.

•

Hourly Time Signal

 

The hourly time signal causes the watch to beep twice every hour

❚To select an alarm or the Hourly Time

Signal screen

Each press of the D button cycles through available screens in the sequence shown below.

Alarm 1

Alarm 2

1.

In the Alarm Mode, use the

 

 

Dbutton to scroll through

 

 

the alarm screens until the

 

 

one whose setting you want

 

 

to change is displayed.

 

•

The alarm number or snooze

Alarm Number

 

 

alarm indicator (SNZ) appears

 

 

at the bottom of the display to

 

 

indicate the current screen.

 

• Holding down either button

changes the setting at high

speed.

• When setting the hour, make

sure you specify AM (A) or

PM (P) correctly when using

12-hour timekeeping, or that

you specify the correct 24-

hour time.

• The same 12-hour/24-hour

format you select for the

(Forward)

on the hour.

When you enter the Alarm Mode, the screen for the alarm that was displayed when you last exited the mode appears first.

Hourly Time Signal

Alarm 3

2. Hold down the A button for about two seconds until the hour digits start to flash on the display.

Alarm on indicator

Timekeeping Mode time is

also applied in the Alarm

Mode.

Timekeeping Mode

Alarm Time

•This also causes the alarm on indicator to appear and automatically turns on the alarm.

AButton

•Enters/exits the setting mode.

BButton

Hour

4. Press the C button to

select the minute setting.

Minute

(Twice)

Alarm Number

Snooze Alarm

Alarm 4

 

 

 

•Scrolls back through the options at the flashing (selected) setting.

CButton

•Moves the flashing between settings.

DButton

•Scrolls forward through the options at the flashing (selected) setting.

5.

Use the D(+) and B (–)

(Back)

 

buttons to change the minute setting.

• Each press of the B(+) and

D(–) button changes the

minute setting in 30-minute

(Forward)

increments.

 

•Holding down either button

changes the setting at high speed.

6. When the setting is the way you want, press the

Abutton.

• This exits the setting screen.

•The display also will exit the setting screen automatically if you do not perform any operation for about two or three minutes.

❚To turn an alarm or the hourly time signal on and off

1. In the Alarm Mode, use the

Dbutton to display the screen for the alarm you

want to turn on or off.

• The alarm number or snooze

alarm indicator (SNZ) appears Alarm Number at the bottom of the display to

indicate the current screen.

2. Press the Abutton to toggle the displayed alarm on or off.

Alarm on indicator

Snooze on indicator

Alarm

Snooze Alarm

Hourly Time Signal on indicator

 

❚To stop the alarm beeper

Press any button.

•In the case of the snooze alarm the alarm will sound again in about five minutes. “SNZ” flashes while the snooze alarm is active (indicating that the alarm will sound again).

•The snooze alarm will be canceled automatically when any of the following occurs while the SNZ indicator is flashing on the display.

•If you turn off the snooze alarm in the Alarm Mode.

•If you enter the Alarm Mode, display the snooze alarm screen, and then display the setting screen.

•If you enter the Timekeeping Mode and then display the setting screen.

❚To test the alarm

In the Alarm Mode, hold down the D button to sound the alarm.

Hourly Time Signal

7