Operation Guide 2696/2832(B)

Stopwatch Mode

 

Configuring Time and Date Settings Manually

 

 

 

The stopwatch measures elapsed time in units of 1/100 second up to 59 minutes, 59.99 seconds (60 minutes). When the maximum limit is reached, the elapsed time automatically returns to zero and timing continues from there.

Normally, you should never need to configure time and date settings manually if you have auto receive turned on and you are within the range of a time calibration signal. If the watch is unable to update its settings automatically for some reason, however, you can configure them manually as described below.

Performing Stopwatch Operations

Timekeeping Mode

Elapsed Time Measurement

Start Stop Reset

Pressing the A button while timing is stopped resets the stopwatch to all zeros.

Cumulative Time Measurement

Time and Date Settings

Timekeeping Mode

(Hold down about two seconds.)

Transmitter

Home City Code

Selection Mode

 

(Three times)

AButton

Split/Reset

Press during elapsed time measurement to display the split time.

Press when elapsed time measurement is stopped to reset the stopwatch to all zeros.

DButton

Start/Stop

Each press starts and stops elapsed time measurement.

Mode Indicator

About two seconds

Seconds

Minutes

1/100 second

Current Time (24-hour format)

Pressing the D button to restart the stopwatch without resetting it to all zeros causes the elapsed time measurement to resume from where it was last stopped.

Split Time Measurement

Start

Record split Release split

Stop

Reset

Pressing the A button while timing is being performed freezes the current elapsed time on the display, but timing of the next split continues internally.

Changing to another mode while a split time is displayed cancels the split time operation.

1st and 2nd Place Finishers

Start

1st finish

2nd finish Displays time

Reset

 

(Displays time

of 2nd finish.

 

 

of 1st finish.)

 

 

Auto Receive

Summer Time

12/24-hour Seconds Hour Minute timekeeping

Power Saving Day Month Year

While the setting screen (the one with a flashing setting) is on the display, use the Cand A buttons to move the flashing between settings.

AButton

Displays the setting screen.

Changes from the first setting group to the next.

Exits the setting screen.

CButton

Moves the flashing between settings.

See “Signal Reception Settings” for information about calibration signal, Home City, summer time, and auto receive settings.

To configure time and date settings manually

2. Press the Abutton to advance to the next group of settings.

5. To restart the seconds count to 00, press the D button.

7. While the Power Saving setting is flashing, press the D button to toggle it

1. In the Timekeeping Mode, hold down the Abutton for about two seconds.

This will cause the watch to beep and display the transmitter selection mode setting screen.

AButton

Displays the setting screen.

Changes from the first setting group to the next.

Exits the setting screen.

BButton

Scrolls back through the options at the flashing (selected) setting.

CButton

Moves the flashing between settings.

DButton

Scrolls forward through the options at the flashing (selected) setting.

Timekeeping Mode

FREQUENCY (Frequency)

This causes the 12/24-hour timekeeping setting to flash.

Example: 12H (12-hour timekeeping)

3. Use the C button so the setting you want to change is flashing on the display.

Use the C button to cycle through the time and date settings shown below. Each press of C causes the applicable setting to flash.

12/24-hour

Seconds

Hour

timekeeping

 

 

Power Saving Day Month

4. While the 12/24-hour timekeeping setting is flashing, press the D button to select the setting you want.

Minute

Year

Pressing the D button while

 

 

the seconds count is in the

 

 

range of 30 to 59 resets it to

Resets to 00.

 

00 and also adds 1 to the

 

 

minutes. Pressing the D

 

 

button in the range of 00 to 29

 

 

resets the seconds count

 

 

without changing the minutes.

 

6.

While the hour, minutes,

(Back)

 

 

year, month, or day setting

 

 

is flashing, use the D (+)

 

 

and B(–) buttons to

 

 

change the setting.

 

(Forward)

Holding down either button changes the setting at high speed.

When setting the hour, make sure you specify AM (A) or PM

(P) correctly, or that you specify the correct 24-hour time.

You can set a date in the range of January 1, 2000 to December 31, 2099.

The day of the week is set automatically in accordance with the date you set.

on (PS On) or off (PS OF).

Use the Cbutton to select each of the settings and the D and Bbuttons to change them.

8. When the settings are the way you want, press the Abutton.

This exits the setting screen.

The display also will exit the setting screen automatically if you do not perform any operation for about two or three minutes.

The watch automatically makes adjustments for leap years and month lengths.

Pressing the Dbutton toggles the timekeeping format between 12-hour (“12H” indicator) and 24-hour (“24H” indicator).

8