Operation Guide 3040
Using the Timer | and Indicators”. |
| Use the Cbutton to enter the Timer Mode as shown under “Modes |
|
|
3. Configure the setting that is flashing.
To set the start time hours and minutes
4. When all of the settings are the way you want, press the
Abutton to exit the setting screen. |
• The display also will exit the setting screen automatically if |
You can set the start time of the timer in units of one minute in the range of 1 to 24 hours. The watch beeps for 10 seconds when the end of the countdown is reached. Turning on the watch’s auto repeat timer feature causes the countdown to restart from the start time whenever the end of the countdown is reached.
Timer Types
You can use either of the two settings describe below to configure timer settings.
•For information about selecting the timer type, see “To configure timer settings”.
Repeat Timer
With the Repeat Timer, the timer stops when the end of the countdown is reached. After about 10 seconds, the original start time
●Auto Repeat Timer
With the auto repeat timer, the timer automatically resets the start time and continues timing when the end of the current countdown is reached.
•The countdown repeats up to eight times, or until you stop it manually.
❚To configure timer settings
1. | While the current starting | Hour | |
| |||
| time is displayed in the |
| |
| Timer Mode, press the A |
| |
| button. |
|
|
• | The hour digits start to flash |
| |
| on the display. This is the |
| |
| setting screen. |
|
|
2. | Use the C button to move | Minute | |
| |||
| the flashing to the setting |
| |
| you want to change. |
|
|
• | Each press of Cmoves the |
| |
| flashing between the settings |
| |
| as shown below. Move the |
| |
| flashing to the digits you want |
| |
| to change. |
|
|
| Hour | Minute | Timer Type |
Use the D(+) and B(–) buttons to change the hour and minute settings.
•Holding down either button changes the setting at high speed.
•To configure the setting to countdown 24 hours, set the start time as 0:00.
To select the timer type
Press the Dbutton to toggle between the auto repeat timer and repeat timer.
•“ON” indicates the auto repeat timer while “OFF” indicates the repeat timer.
Auto Repeat Timer
you do not perform any operation for about two or three | |
|
minutes.
•The auto repeat indicator (
) appears on the display while the auto repeat timer is turned on.
(+)
❚To use the countdown timer
Press the Dbutton to interrupt time calibration signal reception.
•Each press of the Dbutton starts or stops the stopwatch.
•The time counts down in
Hour, Minutes Seconds
Time Up Beeper
The watch beeps for 10 seconds when the end of the countdown is reached.
❚To stop an alarm
Pressing any button while the beeper is sounding stops it.
Using the Stopwatch | under “Modes and Indicators”. | |||
| Use the Cbutton to enter the Stopwatch Mode as shown | |||
|
|
|
| |
The stopwatch measures elapsed time in units of 1/10 second up | ❚ To measure elapsed time | |||
to 23 hours, 59 minutes, 59.9 seconds (24 hours). When the | ||||
|
|
| ||
maximum limit is reached, the elapsed time returns to zero |
|
|
| |
automatically and timing continues from there. | Start | Stop | Reset | |
| ||||
1/10 second
(Reset)
(Start/Stop)
Using the Stopwatch
In the Stopwatch Mode, press the Dbutton to start and stop the stopwatch.
•Each press of the Dbutton starts or stops the stopwatch.
Hour, Minutes Seconds
Cumulative Time Measurement
Pressing the D button to restart the stopwatch without resetting it to all zeros will resume elapsed time measurement from where it was last stopped.
❚To measure split times
•Pressing the Abutton while the countdown is stopped displays the reset time.
•Holding down the Dbutton for about two seconds while a countdown either is ongoing or stopped will reset the timer to its start time.
•Pressing the Dbutton again while the countdown is stopped restarts the countdown.
(Split/Reset)
1/10 second
(Start/Stop)
Start | Split | Release Split | Stop | Reset |
Split Time Screen
Split Indicator 
•Pressing the Abutton while an elapsed time operation is in progress will freeze the current time on the display and continue timing of the next split internally. This condition is
indicated by the “SPL” (split) indicator on the display. Changing to another mode while a split time is displayed cancels the split time operation.
•Pressing the Abutton while the stopwatch is stopped will reset stopwatch to all zeros.
•Holding down the Dbutton for about two seconds while the stopwatch either is performing an elapsed time operation or stopped also will reset it to all zeros.
Release
Split
❚To time 1st and 2nd place finishers
Start | 1st Finisher 2nd Finisher | Displays | Reset |
| (Displays time | time of 2nd |
|
| of 1st finisher.) | finisher. | 7 |
|
|
|