Operation Guide 3184

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A until the city code starts to flash, which indicates the setting screen.

2. Press C and the DST setting screen appears.

3. Use D to cycle through the DST settings in the sequence shown below.

Auto DST (AvtA) DST off (OFF) DST on (ON)

DST indicator

 

If you change your Home City to one that is within the

 

same transmitter area, the current DST setting (Auto

 

DST) will be retained. If you change to a city that is

 

outside your current transmitter area, DST will be

 

turned off automatically.

 

 

Transmitter

Covered City Codes

Japan

TPE, SEL, TYO

China

HKG, BJS

U.S.

HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI, NYC, YHZ, YYT

Europe (U.K., Germany)

LIS, LON, MAD, PAR, ROM, BER, STO, ATH, MOW

None

All other city codes

4. When the setting you want is selected, press A to exit the setting screen.

The DST indicator appears to indicate that Daylight Saving Time is turned on.

Reference

This section contains more detailed and technical information about watch operation. It also contains important precautions and notes about the various features and functions of this watch.

Moon Phase Indicator

The Moon phase indicator of this watch indicates the

Moon Phase indicator

current phase of the Moon as shown below. It is based on

 

 

 

the view of the left side of the moon at meridian transit

 

 

 

 

 

 

from the northern hemisphere of the Earth. If the

 

 

 

appearance of the Moon phase indicator is reversed from

 

 

 

the actual Moon as viewed from your location, you can

 

 

 

use the procedure under “To reverse the displayed Moon

 

 

 

phase” to change the indicator.

 

 

(part you cannot see)

 

 

 

 

 

Moon phase (part you can see)

Moon Phase

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Moon Age

 

28.7-29.8

1.0-2.7

2.8-4.6

4.7-6.4

6.5-8.3

8.4-10.1

10.2-12.0

12.1-13.8

 

0.0-0.9

Moon Phase

 

New

 

 

 

 

 

 

First

 

 

 

 

Moon

 

 

 

 

 

 

Quarter

 

 

 

 

 

 

 

 

 

 

 

 

(Waxing)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Moon Phase

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Moon Age

 

13.9-15.7

15.8-17.5

17.6-19.4

19.5-21.2

21.3-23.1

23.2-24.9

25.0-26.8

26.9-28.6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Moon Phase

 

Full

 

 

 

 

 

 

Last

 

 

 

 

Moon

 

 

 

 

 

 

Quarter

 

 

 

 

 

 

 

 

 

 

 

 

(Waning)

 

 

 

Tidal Movements

Tides are the periodic rise and fall of the water of oceans, seas, bays, and other bodies of water caused mainly by the gravitational interactions between the Earth, Moon and Sun. Tides rise and fall about every six hours. The Tide Graph of this watch indicates tidal movement based on the Moon’s transit over a meridian and the lunitidal interval. The Tide Graph calculates and graphically represents current tide conditions in your Home City or a port city in the vicinity of the Home City based on longitudes, lunar day length, and lunitidal interval preset in watch memory, and on high tide times specified by you.

Tide Graph

The Tide Graph graphically represents the current tide condition using one of three patterns that represent spring tide, intermediate tide, and neap tide, as shown below.

Tide Name

Graph

Description

 

 

 

Spring Tide

 

Large difference between high tide

 

 

and low tide. Occurs a few days

 

 

before and after a New Moon and Full

 

 

Moon.

 

 

 

Intermediate Tide

 

Medium difference between high tide

 

 

and low tide.

 

 

 

Neap Tide

 

Small difference between high tide

 

 

and low tide. Occurs a few days

 

 

before and after the first quarter and

 

 

last quarter of a half Moon.

 

 

 

The Tide Graph flashes as shown below to indicate the tide range.

Low tide

High tide

High tide

The segments on either end of the Tide Graph flash during high tide.

Button Operation Tone

Mute indicator

The button operation tone sounds any time you press one

of the watch’s buttons. You can turn the button operation

 

 

 

 

 

 

tone on or off as desired.

 

 

 

 

 

Even if you turn off the button operation tone, alarms,

 

 

 

the Hourly Time Signal, and other beepers all operate

 

 

 

normally.

 

 

 

 

To turn the button operation tone on and off

 

 

 

 

 

 

1. In the Timekeeping Mode, hold down A until the city

 

 

 

code starts to flash, which indicates the setting screen.

 

 

 

2. Press C nine times until the current button operation

 

 

 

tone setting (

or

) appears.

 

 

 

 

3. Press D to toggle the setting between

(tone on)

 

 

 

and

(tone off).

 

 

 

 

 

4. Press A to exit the setting screen.

 

The mute indicator is displayed in all modes when the button operation tone is turned off.

Power Saving Function

When turned on, the Power Saving function enters a sleep state automatically whenever the watch is left in an area for a certain period where it is dark. The table below shows how watch functions are affected by the Power Saving function.

Power saving indicator

Elapsed Time

Display

Operation

in Dark

 

 

60 to 70 minutes

Blank, with Power Saving

All functions enabled, except for the

 

indicator flashing

display

6 or 7 days

Blank, with Power Saving

Auto receive, beeper tone,

 

indicator not flashing

illumination, and display are disabled.

Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.

The watch will not enter the sleep state between 6:00 AM and 9:59 PM. If the watch is already in the sleep state when 6:00 AM arrives, however, it will remain in the sleep state.

The watch will not enter a sleep state while in the Diving Mode, Stopwatch Mode, or Countdown Timer Mode.

To recover from the sleep state

Perform any one of the following operations.

Move the watch to a well-lit area.

Press any button.

Angle the watch towards your face for reading.

To turn Power Saving on and off

1. In the Timekeeping Mode, hold down A until the city code starts to flash, which indicates the setting screen.

2. Press C 11 times until the Power Saving on/off screen

 

 

 

ll ll

appears.

 

 

 

l

3. Press D to toggle Power Saving on ( ) and off (

).

 

 

 

l

l ll

 

 

 

 

 

l

4. Press A to exit the setting screen.

 

 

 

l

 

l

 

l l

ll

l

The Power Saving indicator is on the display in all

 

l

 

 

ll

 

 

 

 

 

 

modes while Power Saving is turned on.

 

 

On/Off status

 

 

 

 

Radio-controlled Atomic Timekeeping Precautions

Strong electrostatic charge can result in the wrong time being set.

The time calibration signal bounces off the ionosphere. Because of this, such factors as changes in the reflectivity of the ionosphere, as well as movement of the ionosphere to higher altitudes due to seasonal atmospheric changes or the time of day may change the reception range of the signal and make reception temporarily impossible.

Even if the time calibration signal is received properly, certain conditions can cause the time setting to be off by up to one second.

The current time setting in accordance with the time calibration signal takes priority over any time settings you make manually.

The watch is designed to update the date and day of the week automatically for the period January 1, 2000 to December 31, 2099. Setting of the date by the time calibration signal cannot be performed starting from January 1, 2100.

This watch can receive signals that differentiate between leap years and non-leap years.

Though this watch is designed to receive both time data (hour, minutes, seconds) and date data (year, month, day), certain signal conditions can limit reception to time data only.

If you are in an area where proper time calibration signal reception is impossible, the watch keeps the time with the precision noted in “Specifications”.

If you have problems with proper time calibration signal reception or if the time setting is wrong after signal reception, check your current city code, DST (summer time), and auto receive settings.

The Home City setting reverts to the initial default of TYO (Tokyo) whenever the battery power level drops to Level 5 or when you have the rechargeable battery replaced. If this happens, change the Home City to the setting you want.

Transmitters

The time calibration signal received by this watch depends on the currently selected Home City code.

When a U.S. time zone is selected, the watch receives the time calibration signal transmitted from the United States (Fort Collins).

When a Japanese time zone is selected, the watch receives the time calibration signals transmitted from Japan (Fukushima and Fukuoka/Saga).

When a European time zone is selected, the watch receives the time calibration signals transmitted from Germany (Mainflingen) and England (Anthorn).

When a China time zone is selected, the watch receives the time calibration signal transmitted from China (Shangqiu City).

When your Home City is LIS, LON, MAD, PAR, ROM, BER, STO, ATH, or MOW (which can receive both the Anthorn and Mainflingen signals), the watch first tries to pick up the signal it last successfully received. If that fails, it tries the other signal. For the first receive after you select your Home City, the watch tries the nearest signal first (Anthorn for LIS, LON, Mainflingen for MAD, PAR, ROM, BER, STO, ATH, and

MOW).

7

Page 7
Image 7
Casio 3184 manual Reference