Operation Guide 5145
Stopwatch
Use the C button to enter the Stopwatch Mode as shown under “Modes and Indicators” on page 17.
The stopwatch measures elapsed time in units of 1/100 second up to 59 minutes,
59.99seconds (60 minutes). When the maximum limit is reached, the elapsed time returns to zero automatically and timing continues from there.
80
■Starting or Stopping an Elapsed Time Operation
In the Stopwatch Mode, press D to start, stop, or restart the stopwatch.
6SOLW5HVHW
6WDUW6WRS
81
●Stopwatch Display
ξElapsed Time Screen
This screen shows the elapsed minutes and seconds.
0LQXWHV
6HFRQGV
82
ξPaused Elapsed Time Measurement Screen
When elapsed time measurement is paused, the display alternates between a minute/second screen and a 1/100 second screen at
VHFRQGLQWHUYDO
0LQXWHVVHFRQG 6HFRQGV
83
●To measure elapsed time
DDA
StartStopReset
Pressing A while timing is stopped resets the stopwatch to all zeros.
Cumulative Time Measurement
Pressing D to restart the stopwatch without resetting it to all zeros causes the elapsed time measurement to resume from where it was last stopped.
●To measure split times
D |
| A |
|
| A |
| D |
| A |
|
|
|
|
| |||||
Start | Record split | Release split | Stop |
| Reset | ||||
Pressing A while timing is being performed displays the split time screen, but timing continues internally.
ξChanging to another mode while a split time is displayed cancels the split time operation.
●To time 1st and 2nd place finishers
D |
| A |
|
| D |
|
| A |
| A |
|
|
|
|
|
| |||||
Start | 1st Finisher | 2nd Finisher | Displays time of | Reset | ||||||
| (Displays time of |
|
|
| 2nd fi nisher. |
| ||||
| 1st fi nisher.) |
|
|
|
|
|
|
| ||
Pressing D while the split time is on the display stops elapsed time measurement, leaving the split time on the display.
Press A to exit the split time screen and display the total elapsed time when measurement was stopped.
84 | 85 |
|
|
Split Time Indicator | 6SOLWLQGLFDWRU 0LQXWHV 6HFRQGV VHFRQG |
The split time screen cycles alternately through the split indicator (SPL), a minute/ second screen, and a 1/100 second screen.
Alarm and Hourly Time Signal
Use the C button to enter the Alarm as shown under “Modes and Indicators” on page 17.
The watch beeps for about 10 seconds when the Timekeeping Mode time reaches the currently set alarm time. The Hourly Time signal causes the watch to beep every hour on the hour.
|
| ■ Switching between Screens |
|
|
| In the Alarm Mode, press D. |
|
|
| ξEach press of D toggles between the alarm screen and the hourly time signal | |
|
| screen. |
|
|
| ξWhen you enter the Alarm Mode, the screen that was displayed the last time you | |
|
| exited the mode appears fi rst. |
|
|
| ξIn the case of the alarm screen, the display alternates between the alarm ON/OFF | |
|
| setting and the alarm time setting. |
|
86 |
|
| 87 |
$ODUP6FUHHQ | +RXUO\7LPH6LJQDO6FUHHQ | ■ Setting an Alarm Time |
|
| 1. In the Alarm Mode, use D to display the alarm |
| |
| D |
| |
|
| screen. |
|
| 2. Hold down A for about two seconds until the |
| |
|
| VHFRQGLQWHUYDO | |
|
| hour digits start to flash, which indicates the |
|
|
| setting screen. |
|
$ODUPWLPH |
| ξDisplaying the setting screen turns on the alarm |
|
|
| automatically. | +RXU |
|
|
| |
88 | 89 |