Operation Guide 5288
Note
ξ For information about selecting a Home City and confi guring the DST setting, see |
Checking the Current Time in a Different Time Zone
“Confi guring Home City Settings” (page |
ξ While |
for times from noon to 11:59 p.m. No indicator appears for times from midnight to |
11:59 a.m. With |
P (PM) indicator. |
ξ The watch’s |
lengths and leap years. Once you set the date, there should be no reason to |
change it except after you have the watch’s battery replaced. |
ξ The day of the week changes automatically when the date changes. |
Currently selected
World Time City
Current time in the currently selected World Time City
You can use the World Time Mode to view the current time in one of 29 time zones (27 cities) around the globe. The city that is currently selected in the World Time Mode is called the “World Time City”.
To enter the World Time Mode
Use C to select the World Time Mode as shown on page
To view the time in another time zone
In the World Time Mode, use D (East) to scroll through city codes.
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use D (East) to display the
DST indicator city code (time zone) whose Standard Time/Daylight Saving Time setting you want to change.
2. Hold down A for about two seconds.
ξ This toggles the city code you selected in step 1 between Daylight Saving Time (DST indicator displayed) and standard time (DST indicator not displayed).
ξUsing the World Time Mode to change the DST setting of the city code that is selected as your Home City also will change the Timekeeping Mode time DST setting.
ξNote that you cannot switch between standard time/daylight saving time (DST) while GMT is selected as the World Time City.
ξThe standard time/daylight saving time (DST) setting affects only the currently selected time zone. Other time zones are not affected.
Countdown Timer
|
|
| The countdown timer can be set within a range of |
|
|
| one minute to 60 minutes. An alarm sounds when the |
|
|
| countdown reaches zero. The countdown timer also has |
|
|
| an |
|
|
| the progress of the countdown. |
|
|
| To enter the Countdown Timer Mode |
|
|
| Use C to select the Countdown Timer Mode as shown |
|
|
| on page |
|
|
|
|
Minutes | Seconds Configuring the Countdown Timer | ||
|
|
| The following are the settings you should configure |
|
|
| before actually using the countdown timer. |
|
|
| Countdown start time; |
|
|
| beeper on/off |
|
|
ξSee “To confi gure the countdown timer” on page
Auto-repeat
When
When
ξPressing D while an
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed about the countdown status without looking at the display. The following describes the types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
ξWhen the progress beeper is turned off, the countdown end beeper sounds for about 10 seconds, or until you press any button to stop it.
ξWhen the progress beeper is turned on, the countdown end beeper sounds for about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown progress as described below.
ξStarting from fi ve minutes before the end of the countdown, the watch emits four short beeps at the top of each countdown minute.
ξ30 seconds before the end of the countdown, the watch emits four short beeps.
ξThe watch emits a short beep for each of the last 10 seconds of the countdown.
ξIf the countdown start time is six minutes or greater, the watch emits a short beep for each second of the fi nal 10 seconds before the fi
To configure the countdown timer
1.While the countdown start time is on the display in the Countdown Timer Mode, hold down A until the current countdown start time starts to flash, which indicates the setting mode.
ξ If the countdown start time is not displayed, use the procedure under “To perform a countdown timer operation” (page
2.Press C to move the flashing in the sequence shown below to select other settings.
C C
Start Time | Progress Beeper |
3.When the setting you want to change is flashing, use B and D to change it as described below.
Setting | Screen |
| Button Operation |
|
|
Start Time |
| Use D (+) and B |
| ||
| ξ You can set a start time in the range of 1 to 60 minutes in | ||||
|
|
|
|
| |
| Press D to toggle | displayed) and off | |||
| ( | displayed). |
|
| |
|
|
|
| ||
Progress Beeper |
| Press D to toggle the progress beeper on ( | ) and off | ||
| ( | ). |
|
| |
|
|
|
| ||
4.Press A to exit the setting mode.
ξYou can also perform steps 1 and 2 of the above procedure whenever you need to view the current
| C |
To perform a countdown timer operation |
|
|
| Using the Stopwatch | |||||
D |
| D |
| D |
| D |
| A | The stopwatch measures elapsed time, split times, and two finishes. |
|
|
|
| ||||||
Start | Stop | (Restart) | (Stop) | Reset |
| ||||
ξBefore starting a countdown timer operation, check to make sure that a countdown operation is not in progress (indicated by the seconds counting down). If it is, press D to stop it and then A to reset to the countdown start time.
To stop the alarm
Press any button.
To enter the Stopwatch Mode
Use C to select the Stopwatch Mode as shown on page
Minutes Seconds