Operation Guide 5283/5332

Selecting a Mode

•Press C to cycle between the modes as shown below.

•In any mode (except when a setting mode, with flashing digits is on the display), press B to illuminate the display.

Timekeeping ModeWorld Time ModeCountdown Timer ModeStopwatch ModeAlarm ModeHand Setting Mode

C

C

C

C

 

C

 

 

 

 

C

 

E-10

 

 

 

 

E-11

General Functions (All Modes)

The functions and operations described in this section can be used in all of the

Timekeeping

modes.

Auto Return Features

If you leave a setting mode with flashing digits on the display for two or three minutes without performing any operation, the watch exits the setting mode automatically.

Initial Screens

When you enter the World Time Mode or Alarm Mode, the data you were viewing when you last exited the mode appears first.

Scrolling

The B and D buttons are used on the setting mode to scroll through data on the display. In most cases, holding down these buttons during a scroll operation scrolls through the data at high speed.

Minutes

Hour

Day of week

Use the Timekeeping Mode to set and view the current time and date.

•Each press of D cycles the digital display contents as shown below.

Day of the Week Month-Day Hour : Minutes

Seconds

D D D

PM indicator

D

E-12

E-13

 

 

Configuring Home City Settings

There are two Home City settings: actually selecting the Home City, and selecting either standard time or daylight saving time (DST).

2.Press C twice to move the flashing to the city code.

•For details about city codes, see the “City Code Table” at the back of this manual.

3. Press D (East) and B (West) to select the city code

Note

• After configuring Home City and/or Daylight Saving Time

you want to use as your Home City.

• Keep pressing D or B until the city code you want

(summer time) settings, be sure to adjust the analog

City Code

to select as your Home City appears on the display.

Seconds

E-14

hands to match the digital settings.

• See “Adjusting the Analog Hand Setting” (page E-36).

To configure Home City settings

1.In the Timekeeping Mode, hold down A for about two seconds until the seconds start to flash. This is the setting mode.

•The watch will exit the setting mode automatically if you do not perform any operation for about two or three minutes.

4. After the setting is the way you want, press A to return to the Timekeeping Mode.

Note

•After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate the current time for other time zones based on the current time in your Home City.

* Coordinated Universal Time, the world-wide scientific standard of timekeeping. The reference point for UTC is Greenwich, England.

E-15

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A for about two

DST indicatorseconds until the seconds start to flash. This is the setting mode.

2. Press C to display the DST setting mode.

3. Press D to toggle between Daylight Saving Time (On)

and Standard Time (OFF).

4. After the setting is the way you want, press A to return to the Timekeeping Mode.

•The DST indicator appears to indicate that Daylight Saving Time is turned on.

Adjusting the Digital Time and Date Settings

Use the procedure below to adjust the digital time and date settings.

Note

•After adjusting the digital time and date setting, be sure to adjust the analog hands so the settings match.

•See “Adjusting the Analog Hand Setting” (page E-36).

To configure the digital time and date settings

1.In the Timekeeping Mode, hold down A for about two seconds until the seconds start to flash. This is the setting mode.

Seconds

E-16

E-17

 

 

2. Press C to move the flashing in the sequence shown below to select the other settings.

 

 

C

 

 

 

 

 

C

 

 

 

 

 

 

 

C

 

 

 

 

 

C

 

 

Seconds

 

 

 

DST

 

 

 

Home City Code

 

 

 

Hour

 

 

 

Minutes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Illumination Duration

 

 

 

 

Day

 

 

Month

 

 

Year

 

 

 

 

12/24-Hour Format

 

C

 

C

C

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•The following steps explain how to configure timekeeping settings only.

3.When the timekeeping setting you want to change is flashing, use D and/or B to change it as described below.

Screen

To do this:

Do this:

 

Reset the seconds to 00

Press D.

 

 

 

 

Toggle between Daylight Saving Time (ON)

Press D.

 

and Standard Time (OFF)

 

 

 

Change the city code

Use D (East) and B (West).

 

 

 

 

Change the hour or minute

Use D (+) and B (–).

 

 

 

 

Toggle between 12-hour (12H) and 24-hour

Press D.

 

(24H) timekeeping

 

 

Change the year, month, or day

Use D (+) and B (–).

 

 

 

4. Press A to exit the setting mode.

E-18

E-19