Casio 5332 Using the Alarm, Adjusting the Analog Hand Setting, Illumination, SPL, SPL, SNZ, AL1, AL4, SIG, AL1, AL2, AL3, AL4, SNZ, Stop, Stop, Stop, Note, Start, Reset

Operation Guide 5283/5332

To perform an elapsed time operation

D	D	D	D	A
Start	Stop	(Restart)	(Stop)	Reset
To pause at a split time
D	A	A	D	A
Start	Split	Split release	Stop	Reset
	(SPL displayed)
To measure two finishes
D	A	D	A	A
Start	Split	Stop	Split release	Reset
	(SPL displayed)	Second runner	Display time of
	First runner finishes. finishes.		second runner.
	Display time of first
	runner.
E-30

Note

•The Stopwatch Mode can indicate elapsed time up to 59 minutes, 59 seconds.

•Once started, stopwatch timing continues until you press D to stop it, even if you exit the Stopwatch Mode to another mode and even if timing reaches the stopwatch limit defined above.

•Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement.

E-31

Using the Alarm

To enter the Alarm Mode

Use C to select the Alarm Mode as shown on page E-11.

Alarm number

Alarm time (Hour : Minutes)

E-32

You can set five independent daily alarms. When a daily alarm is turned on, an alarm tone will sound for about 20 seconds each day when the time in the Timekeeping Mode reaches the preset alarm time. One of the alarms is a snooze alarm, while the other four are one-time alarms. The snooze alarm operation will repeat every five minutes, up to seven times.

You can also turn on an Hourly Time Signal, which will cause the watch to beep twice every hour on the hour.

•The snooze alarm screen is indicated by SNZ, while the other alarm screens are numbered AL1 through AL4. The Hourly Time Signal screen is indicated by SIG.

•When you enter the Alarm Mode, the data you were viewing when you last exited the mode appears first.

E-33

To set an alarm time

Alarm ON/OFF indicator	1. In the Alarm Mode, use D to scroll through the alarm
	screens until the one whose time you want to set is
	displayed.
		D	D	D	D	D

5. Press A to exit the setting mode.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn an alarm and the Hourly Time Signal on and off

AL1 AL2 AL3 AL4 SNZ SIG

D

2.Hold down A for about two seconds until the alarm time starts to flash. This is the setting mode.

3.Press C to move the flashing between the hour and minute settings.

4.While a setting is flashing, use D (+) and B (–) to change it.

•When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator).

E-34

Hourly time signal on indicator

Snooze alarm indicator

1.In the Alarm Mode, use D to select an alarm or the Hourly Time Signal.

2.When the alarm or the Hourly Time Signal you want is selected, press A to toggle it between on and off.

•The alarm on indicator (when any alarm is on), snooze alarm indicator (when the snooze alarm is on), and the Hourly Time Signal on indicator (when the Hourly Time Signal is on) are shown on the display in all modes.

To stop the alarm

Press any button.

E-35

Adjusting the Analog Hand Setting

Use the following procedure to adjust the analog hands so their settings match the digital time.

To adjust the analog time

1. Use C to select the Hand Setting Mode as shown on page E-11.

2.Hold down A until the current digital time starts to fl ash, which indicates the analog setting mode.

3. Press D to advance the analog time setting by 20 seconds.

•Holding down D advances the analog time setting

at high speed.

•If you need to advance the analog time setting a long way, hold down D until the time starts advancing at high speed, and then press B. This locks the high- speed hand movement, so you can release the two buttons. High-speed hand movement continues until you press any button. It will also stop automatically after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal, or countdown beeper) starts to sound.

4.Press A to exit the setting mode.

•The watch will automatically adjust the minute hand slightly to match its internal second count when you exit the setting mode.

•To return to the Timekeeping Mode, press C.

E-36 E-37

Illumination

The face of the watch is illuminated for easy reading in the dark.

To turn on illumination

In any mode (except when a setting mode, with flashing digits is on the display), press Bto illuminate the display.

• You can use the procedure below to select either 1.5 seconds or 3 seconds as the illumination duration. When you press B, the display will remain illuminated for about 1.5 seconds or 3 seconds, depending on the current illumination duration setting.

To change the illumination duration

1.In the Timekeeping Mode, hold down A until the seconds start to flash. This is the setting mode.

2.Press C nine times so the illumination duration setting mode is on the display.

3. Press D to toggle the illumination duration between 1.5 seconds ( ) and 3 seconds ( ).

4. After the settings are the way you want, press A to exit the setting mode.

Illumination Precautions

•Illumination may be hard to see when viewed under direct sunlight.

•Illumination turns off automatically whenever an alarm sounds.

•Frequent use of illumination runs down the battery.

E-38 E-39