E-27
Hourly time signal on indicator
Alarm on indicator

Operation Guide 5208

Alarms

The Alarm Mode lets you configure five daily alarms. You also can use it to turn the Hourly Time Signal on or off.

•The watch beeps for about 10 seconds when an alarm

time is reached.

•Turning on the Hourly Time Signal causes the watch to beep on the hour every hour.

• All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C(page E-9).

Alarm time (Hour : Minutes)

E-20

2.After you select an alarm, hold down A for about two seconds until the hour setting

of the alarm time starts to flash. This is the setting mode.

• This operation turns on the alarm automatically.

3.Press Cto move the flashing between the hour and minute settings.

4.While a setting is flashing, use D(+) and B (–) to change it.

5.Press Ato exit the setting mode.

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the watch is in.

•Alarm and Hourly Time Signal operations are performed in accordance with the Timekeeping Mode time.

•To stop the alarm tone after it starts to sound, press any button.

E-22

Countdown Timer

Timer 1

Timer 2

 

A

 

▲

 

▲

 

2 seconds

Seconds

Seconds

Minutes

Minutes

Dual timers can be set with two different starting times. The watch can be configured so the two timers alternate, so when one reaches the end of its countdown, the other timer starts. You can specify a “number of repeats” value from 1 (once) to 10 (ten times), which controls how many times the two-timer countdown operation is performed. The starting time of each timer can be set in five-second steps up to 99 minutes, 55 seconds.

E-24

2.Press Cto move the flashing in the sequence shown below to select other settings.

Timer 1

 

 

Timer 1

 

 

Timer 2

 

 

Timer 2

Minutes

 

 

Seconds

 

 

Minutes

 

 

Seconds

Number of Repeats

3.When the setting you want to change is flashing, use D and Bto change it as described below.

Setting

Screen

Button Operation

Minutes, Seconds

 

Use D (+) and B (–) to change the setting.

 

 

 

Number of Repeats

 

Use D (+) and B (–) to change the setting.

 

 

 

•To disable either timer, set 00'00" as its countdown start time.

4.Press A to exit the setting screen.

E-26

• Even if you exit the Countdown Timer Mode, the countdown timer operation

continues and the watch beeps as required.

To set an alarm time

Alarm number

Alarm time

 

About 2 seconds

▲

▲

1.In the Alarm Mode, use D to scroll through the alarm screens until the one whose time you want to set is displayed.

AL1 AL2 AL3

SIG AL5 AL4

•The alarm screens are AL1, AL2, AL3, AL4, and AL5.

E-21

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.

2. Press A to toggle it on and off.

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select the Hourly Time Signal (SIG) (page E-21).

2. Press A to toggle it on and off.

E-23

The watch emits a short beep whenever either of the timers reaches the end of its countdown during an ongoing timer operation. The watch emits a 5-second beep when the end of the final timer operation (specified by the number of repeats) is reached.

•All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C(page E-9).

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero. The beeper stops after about 5 seconds or when you press any button.

To configure the countdown timer

1.While the countdown start time is on the display in the Countdown Timer Mode, hold down Auntil the current countdown start time starts to flash, which indicates the setting screen.

•If the countdown start time is not displayed, use the procedure under “To use the countdown timer” (page E-27) to display it.

 

 

E-25

To use the countdown timer

 

 

Current timer time Timer (1 or 2)

A

Current repeat count

 

 

 

▲

 

(Reset)

▲

 

 

 

 

2 seconds

 

(Start/Stop)

Preset number of repeats

 

 

Press Dwhile in the Countdown Timer Mode to start the countdown timer.

•Pressing A while a countdown is in progress will display the repeat count (current repeat count/preset number of repeats). The ongoing countdown will reappear automatically after about two seconds.

•The countdown is performed by alternating between Timer 1 and Timer 2. A short beep is emitted to signal a changeover from one timer to the other.

•Pressing Awhile a countdown timer is stopped resets that time to the start time specified by you.

•Press Dto pause a countdown. Press D again to resume.

•The watch emits a 5-second beep when the end of the final timer operation

(specified by the number of repeats) is reached.

Stopwatch

• To stop a countdown operation completely, first pause it (by pressing D), and then

press A. This returns the countdown time to its starting value.

Minutes

Seconds

The stopwatch lets you measure elapsed time, split times, and two finishes.

•The display range of the stopwatch is 59 minutes, 59.99 seconds.

•The stopwatch continues to run until you stop it. If it reaches its limit, it restarts from zero.

•Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement.

•The stopwatch measurement operation continues even if you exit the Stopwatch Mode.

•All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C (page E-9).

E-28

E-29