4.7.4 Sample Message
4.7.4.1 Enabling On Click
Header Block (Hexadecimal)
No. | Data |
|
00 | F0 | [System Exclusive Status] |
01 | 44 | [Manufacturer's ID] 44H = CASIO ID |
02 | 7E | [Model ID MSB] |
03 | 02 | [Model ID LSB] |
04 | 00 | [Message Version] |
0510 SysEx Device Id
-- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Data Block No. Data
0640 Message Type
0720 Message Id
0802 CAT_TG
0902 Type Id LSB : **02H
1000 Type Id MSB : 00**H
1100 MdevId LSB : **00H
122F MdevId MSB : 2F**H
1301 Section Number LSB : **01H Temporary Area
1400 Section Number MSB : 00**H Temporary Area
1500 Parameter Set Number LSB : **00H Drawbar Preset 0
1600 Parameter Set Number MSB : 00**H Drawbar Preset 0
170E Parameter ID LSB
1800 Parameter ID :
1908 Parameter ID MSB & Block Number & Array Flag
2000 Main Block
2100 Common Block or Drawbar Setting Block
2200 Wave Select Block
2300 Number of Data Bit - 1 : 1bit - 1
2401 Data ( Set OnClick )
-- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
EOX
No. Data
25F7 [EOX]
4.8 Effects
4.8.1 Organization of Effects
There are approximately 30 types of effects, with one or more effect presets, indicated by Num, for each.
The mixer has the effect parts shown below. On the
+ |
|
| ||||||
|
|
|
|
|
|
| ||
|
| |||||||
|
|
|
|
|
| + |
| |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| [Sys Reverb | ||||||
|
|
|
|
|
|
|
|
|
+ |
|
|
|
|
| |||
| [DSP2] |
|
|
|
|
|
|
|
+ |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
+ |
|
|
|
|
| |||
| [DSP4] |
|
|
|
|
|
|
|
+ |
|
|
|
|
| |||
Each of the four DSPs also contains four parallel effector frames. This means that there is a total of 20 effector frames.
4.8.2 Effect Select Operation
To use a desired effect, you must first load its preset effect data.
Preset effects are selected by the patch parameter operation that specifies the sound source system configuration.
The following describes the actual operation.
*The patch parameter effect select block MdevID, TypeID, and Num operations are used to call the desired effect from among the presets.
*The patch parameter effect macro select block Num operation is used to call the effect macro (DSP) from among the presets.
*The effect macro parameter effect type and effect num operations are used to call the desired effect from among the presets. 4.8.2 is performed at the same time.
More concretely, effect preset data is allocated to all of the 20 effect frames. Though there are a number of effect preset data for each effect type, the actual number depends on the selected Type. Refer to the
The effect select and recall operation is performed using a patch parameter change, so this section does not include information about messages. See the explanation about patch parameter effect selection for information about effect selection.
4.8.3 Effect Load Precautions
4.8.3.1 Parts
Effect parts can be classified according to the five groups shown below. Only the effects of the types listed below each part are valid for each part.
*DSP
1.Thru
2.Stereo Thru
3.Noise Gate
4.Compressor/Limiter
5.Stereo Compressor/Limiter
6.Slow Attack
7.3 Band EQ
8.Stereo 3 Band EQ
9.Enhancer
10.Stereo Enhancer
11.Wah
12.Auto Wah
13.Distortion
14.Gt.Amp Simmurator
15.Rotary Speaker
16.Phaser
17.Stereo Phaser
18.Chorus
19.Stereo Chorus
20.Flanger
21.Delay
22.Stereo Delay
23.Stereo Tap Delay
24.Gate Reverb
25.Ring Modulator
26.Tremolo
27.Auto Pan
28.
29.Stereo
*System Chorus
1.System Chorus
*System Reverb
1.System Reverb
*Master
1.Stereo Thru
2.Stereo Comp/Lim
3.Stereo 3Band EQ
4.Stereo Enhancer
5.Surround
6.Stereo
29