Casio QV-120 Using the Self-Timer, Displaying Images on the Camera’s LCD, Displaying Images on a TV Screen, Low Battery Indicator, Memory Full Message, Playing Back Images

	Recording Images		Operation
• The manual exposure adjustment procedure (page 25) cannot be			Using the Self-Timer
used when an exposure warning indicator is on the LCD. Clear the			With	the	Self-Timer, the shutter is released 10 seconds after	you
warning indicator by changing the aperture switch setting.
			press the		/PROTECT button.
• Pressing the [+] or [–] button to adjust exposure while an exposure
			1. Enter the Record Mode.
warning indicator is on the LCD causes a +/– exposure value to
appear. This is an EV value.				• Set the function switch to the REC position.
Low Battery Indicator		2.		Start the Self-Timer operation.
				• Place the camera securely on a tripod, desk or other stable
The low battery indicator (	) appears on the LCD whenever re-
					surface, with the image to be recorded in the LCD.
maining battery power drops below a certain level.				•	After composing the image, press the	/PROTECT but-
When this indicator appears, replace all four batteries with a fresh set
					ton.
of new ones. Once the low battery indicator appears, you can expect
				•	A 10-second countdown starts on the LCD. The shutter will
only about 10 more minutes (alkaline batteries) of operation before
					release automatically when the end of the countdown	is
total power failure.
					reached.
• See page 13 for details on how to replace batteries.
				• To cancel on ongoing Self-Timer operation, press the		/
Memory Full Message					PROTECT button or shutter button.
If you are recording images in the Fine Mode and there is not enough			Note
memory for further Fine Mode recording, the message “REMAIN”			• If you use the Self-Timer with the lens body rotate 180			° (page 22),
appears on the monitor screen along with a value that shows how			you can view the countdown on the LCD while waiting for the shut-
many images can still be recorded in the Normal Mode. You can			ter to release.
press MODE at this time to change to the Normal Mode and record			Important!
more image if you want.
The message “MEMORY FULL” means that there is not enough			• If battery power is low, camera power may turn off while a count-
memory for further recording in any mode. In this case, you have to			down is in progress. If this happens, replace the batteries with new
use the following procedures make room in memory for further			ones.
recording.

•Delete some images from memory (page 46)

•Change the resolution of some of the stored images from FINE to NORMAL (page 50)

2930

Playing Back Images		Playing Back Images		Operation
This section describes how to recall and view images stored in cam-				Notes
era memory.				•	If you set the function switch to PLAY after recording an image, that
Displaying Images on the Camera’s LCD					image appears on the LCD first.
				• The message “MEMORY EMPTY” appears on the LCD if there are
Camera memory is divided into “pages”, and each image is assigned
					no images stored in memory when you enter the Playback Mode.
to page that is numbered sequentially from 1 through 96 (NORMAL
resolution images). Note that all 96 pages are available only if all				Displaying Images on a TV Screen
images are recorded using the NORMAL Mode (page 24).				Use the special video cable that comes with the camera to connect it
The following	procedure describes how to	display images on the
				to a television as illustrated below, and you can then view the images
camera’s built-in LCD.
				stored in camera memory on the TV’s screen.
1. Enter the Playback Mode and turn on the camera.
				Important!
• Slide the function switch to the				•	The camera can be connected only to a TV that is equipped with a
PLAY position.			REC		VIDEO IN terminal.
• When power comes on, the page			PLAY	•	Make sure that the power of both the camera and the TV are turned
that was displayed when you last					off when making connections.
turned power off appears on		the		•	The signal output through this camera's VIDEO OUT terminal is an
LCD.
					NTSC signal. An image output through this terminal will not look
2. Scroll through the memory pages until the image you want
					normal if the camera is connected to a PAL or other type of TV or
to view is displayed.					video deck.	Accessory video cable
• Press [+] to display the next memory page or [–] to display
					TV	VIDEO OUT
the previous memory page.						terminal
•	To jump to the first (lowest numbered) image in memory,					INPUT
press the shutter button and [–] button at the same time.					L	R VIDEO
						AUDIO
• Holding down [+] or [–] for about two seconds starts high-
speed scrolling of images.					VIDEO IN terminal
	[+]	[+]		After connecting the camera and TV, set the channel of the TV to the
				channel used for video input.
	[–]	[–]		After connecting the camera and TV, use the same procedures as
				those described under “Displaying Images on the Camera’s LCD” on
				page 31.
			31	32