3
Maintenance

To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and

wipe it off with a dry cloth.

Replacing the battery

Computer

If turns on, replace the battery. Install a new lithium battery

(CR2032) with the (+) side facing upward. After the battery change,

go through the restart operation, by pressing the AC button.

Then restart the computer according to “How to restart”. *

Sensor

Replace the battery when the Speed digit flashes while riding.

After replacement, check the positions of the sensor and magnet.

After the battery is replaced, ID setting is required again. For *
details, refer to “Sensor ID setting” on the menu screen.
Troubleshooting

MODE does not work when the computer is mounted on its bracket.

Check that there is no dirt between the bracket and the computer.
Wash off the bracket with water to get rid of any dirt.

The sensor signal reception icon does not flash (the speed is not displayed). (Move the com-

puter near the sensor, and turn the front wheel. If the sensor signal reception icon flashes, this

trouble may be a matter of transmission distance due to battery drain, but not any malfunction.)

Set the sensor ID.
Set the ID according to “Sensor ID setting” on the menu screen.
Check that the clearance between the sensor and magnet is not too large. (Clearance: within 5 mm)
Check that the magnet passes through the sensor zone correctly.
Adjust the positions of the magnet and sensor.
Check that the distance between the computer and sensor is correct. (Distance: within 20 to 70 cm)
Install the sensor within the specified range.
Is the computer or sensor battery weak? In winter, battery performance diminishes.
Replace with new batteries. After replacement, follow the procedure “Replacing the battery”.

Incorrect data of the sea level altitude.

Is the sea level altitude corrected?
The sea level altitude may vary due to changes in atmospheric pressure. Correct the sea level altitude ac-
cording to “Sea level altitude correction” on the menu screen.

No display.

Is battery in the computer run down?
Replace it. Then restart the computer referring to “How to restart”.

Incorrect data appear.

Restart the computer referring to “How to restart”.
COIN
COIN

Standard parts

Optional parts

Specification
Battery ..........Computer : Lithium battery (CR2032) x 1, Sensor : Lithium battery (CR2032) x 1
Battery life ....Computer :
Approx. 10 months (If the computer is used for 1 hour/day; the battery life will vary depending on the conditions of use.)
Sensor :
Approx. 8 months (If the computer is used for 1 hour/day; the battery life will vary depending on the conditions of use.)
This is the average figure of being used under 20 °C temperature and the distance between the computer *
and the sensor is 65 cm.
Controller .....8 bite, 1-chip microcomputer (Crystal controlled oscillator)
Display .........Liquid crystal display
Sensor..........No contact magnetic sensor
Transmission distance .......Between 20 and 70 cm
Wheel circumference range
...0100 mm - 3999 mm (Initial value A: 2096 mm, B: 2050 mm)
Working temperature ..........32 °F - 104 °F (0 °C - 40 °C) (This product will not display appropriately when exceeding the Working
Temperature range. Slow response or black LCD at lower or higher temperature may happen respectively.)
Dimensions/weight ............Computer : 2-1/4 x 1-11/32 x 19/32 (57 x 34 x 15 mm) / 1.05 oz (30 g)
Sensor : 1-41/64 x 1-3/8 x 19/32 (41.5 x 35 x 15 mm) / 0.53 oz (15 g)
The factory-loaded battery life might be shorter than the above-mentioned specification.*
The specifications and design are subject to change without notice.*
CR2032
Open
Open
Close
Close
CR2032
#160-2890
Parts kit
#160-2880
Speed sensor
#160-0280
Bracket band
#166-5150
Lithium battery
(CR2032)
#160-2770
Bracket holder
#169-9691
Wheel magnet
#160-2193
Bracket