Cateye CC-COM10W manual How to restart, Maintenance, Specification, Replacing the battery

How to restart

After changing the battery, or when the computer displays an error, restart the computer according to the following procedure.

*With the restarting operation, the speed unit, date, tire size, and record data in the data view are retained.

*When the restarting operation is performed before 0:00 in the morning, the trip distance and the Car- bon offset for the day are not saved due to the data view’s update timing. To retain the measurement data for the day, perform the restarting operation before starting measurement on the next day.

Refer to “Data view’s update timing” for the procedure to save the data view.

1.Press the AC button on the back of the computer.

2.Set the date. To set the date, refer to “Preparing the computer-3”.

*At the time of setting the date, the latest record date in the data view is initially displayed, and any date before that cannot be set.

3.Set the clock. Refer to “Preparing the computer 4”.

Maintenance

To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth.

Specification

Battery	Computer : Lithium battery (CR2032) x 1, Sensor : Lithium battery (CR2032) x 1
Battery life	Computer : Approx. 1 years (If the computer is used for 1 hour/day; the battery life will vary
			depending on the conditions of use.)
	Sensor :		Unit Total Distance reaches about 10000 km (6250 mile)
	*	It may be shortened significantly when backlight is used frequently.
	*	This is the average figure of being used under 20 °C temperature and the distance between the
		computer and the sensor is 65 cm.
Controller	..........................		4 bit, 1-chip microcomputer (Crystal controlled oscillator)
Display			Liquid crystal display
Sensor			No contact magnetic sensor
Transmission distance			......Between 20 and 70 cm
Tire circumference range			......0100 mm - 3999 mm (Initial value: 2096 mm)
Working temperature			32 °F - 104 °F (0 °C - 40 °C) (This product will not display appropriately when
			exceeding the Working Temperature range. Slow response or black LCD at lower or

higher temperature may happen respectively.) Dimensions/weight Computer : 2-9/32” x 1-1/2” x 3/4” (58 x 38 x 19 mm) / 1.02 oz (29 g)

Sensor : 1-41/64” x 1-3/8” x 19/32” (41.5 x 35 x 15 mm) / 0.53 oz (15 g)

*The factory-loaded battery life might be shorter than the above-mentioned specification.

*The specifications and design are subject to change without notice.

Replacing the battery

Computer

If turns on, replace the battery. Install a new lithium battery (CR2032) with the (+) side facing upward. After the battery change, go through the restart operation, by pressing the AC button.

* Then restart the computer according to “How to restart”.

Sensor

When the speed is not displayed even after adjusting cor- rectly, replace the battery. Install a new lithium battery (CR2032) with the (+) side facing upward. After replacement, check the positions of the sensor and magnet.

Close COIN

Open CR2032

CR2032

Close	COIN
Open

Standard parts #160-2196		#160-2193	#169-9691	Optional parts
#160-2190	Speed sensor	Bracket	Wheel	#160-2770
			magnet
Parts kit				Bracket holder
	#160-0280
	Bracket band	#166-5150
		Lithium battery (CR2032)

Troubleshooting

MODE does not work when the computer is mounted on its bracket.

Check that there is no dirt between the bracket and the com puter.

Wash off the bracket with water to get rid of any dirt.

The sensor signal reception icon does not flash (the speed is not displayed). (Move the com- puter near the sensor, and turn the front wheel. If the sensor signal reception icon flashes, this trouble may be a matter of transmission distance due to battery drain, but not any malfunction.)

Check that the clearance between the sensor and magnet is not too large. (Clearance: within 5 mm) Check that the m agnet passes through the sensor zone correctly.

Adjust the positions of the magnet and sensor.

Is the com puter installed at the correct angle?

Back of computer must face toward the sensor.

Check that the distance between the computer and sensor is correct. (Distance: within 20 to 70 cm)

Install the sensor within the specified range.

Is the com puter or sensor battery weak?

In winter, battery perform ance dim inishes.

Replace with new batteries. After replacement, follow the procedure “Replacing the battery”.

No display.

Is battery in the com puter run down?

Replace it. Then restart the computer referring to “How to restart”.

Incorrect data appear.

Restart the computer referring to “How to restart”.

3