®

CAT EYE ENDURO 8

CYCLOCOMPUTER CC-ED300

E: Owner’s Manual

ENDURO8

U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending

Copyright © 2002 CAT EYE Co. Ltd.

CCMED3-021210 066600240 1

• Pay attention to the road or trail! Do not be distracted by the computer.

Warning

• Be sure to securely mount the magnet, the sensor, and the

bracket on your bicycle. Periodically check to insure they are

 

 

mounted securely and the screws are not loosen.

 

• Keep batteries out of reach of small children. Dispose of batter-

 

ies according to local regulations.

 

• Avoid unnecessary prolonged exposure to the sun. Never at-

 

tempt to disassemble the computer head.

Important

• Don’t use thinner, benzene or alcohol to wipe the surface of the

Note

computer. They may damage the surface of computer.

Please read these instructions carefully before attempting to install and use your CAT EYE ENDURO 8 computer so that you understand the functions of this product.

Please don’t throw away this manual, Keep the manual at a place easily accessible.

Computer Set-up(For 1st use or after replacing the battery)

Installation of the Computer on Your Bike

The computer is combined with the following parts.

 

 

 

2

3

 

 

 

 

1

 

 

 

4

 

 

 

 

5

6

7

 

8

1 Bracket

5 Magnet

2 Cord

6 Bracket Rubber Pad

3 Sensor

7 Five Nylon Ties

4 Sensor Rubber Pad

8 Spiral Tube

3

8 7

2

1

All Clear

 

 

 

1 Push three buttons (MODE, START/

 

 

 

STOP and SET) at the same time.

 

 

 

* Do this procedure without fail for

 

 

 

stable measurement when you use

 

 

 

this system for the first time and every

 

 

 

time the battery is replaced.

 

 

 

SET Button

 

 

 

 

 

SET Button

Contact Point

START/STOP

START/STOP Button

 

MODE Button

 

 

Button

 

 

 

 

 

MODE Button

!

You need to know the tire

Select The Measurement Unit

circumference (L cm) be-

2 Select the measurement unit, kilometer

 

forehand.

 

or mile, by pushing the MODE button.

 

 

 

Mount the magnet

 

 

5

1 5 on a spoke of the front wheel so that the surface

 

Sensor Side

of the magnet will face the sensor.

 

 

Spoke

 

 

 

Mount sensor and adjust the gap between the

 

Front Fork

 

 

2 magnet and the sensor.

 

 

 

Secure the sensor 3 with the larger nylon ties 7 at

 

 

the appropriate place and in the right direction.

3

 

 

 

7

 

 

 

Important Note

 

 

Front Fork

 

Marked Line

Mount the sensor 3 at the appropri-

 

 

 

 

ate position so that the center of the

 

 

 

magnet 5 will align with the

 

 

5

marked line on the sensor when the

3

 

wheel is rotated.

 

 

 

 

3

 

 

 

Important Note

 

 

 

Rotate the sensor on the front fork to 5

 

 

 

adjust the gap between the sensor

 

 

 

and the magnet 5 within 5 mm, and

 

 

Within 5 mm

secure it with the nylon ties.Center

3 Mount The Bracket

Secure the cord on the fork with the nylon ties 7 and lead to the handle bar along the outer cable of the bicycle by means of the spiral tube 8.

Put the rubber pad 6 on the bracket 1 and secure the bracket on the handle bar with the screw. Slide the computer into the bracket 1 until you hear the click sound.

The contact points are automatically closed. When you need to detach the computer, slide forward the computer with the lever pushed simultaneously.

Note Allow enough wire clearance in the area marked with an to insure that you can turn the handlebar from left to right without pulling the wire.

1

1

 

 

 

 

Lever

8

 

 

 

6

 

7

 

1

 

 

 

 

Rotate the front wheel.

Test The Basic Functions

 

 

4 Rotate the front wheel gently and see if the computer indicates the

 

running speed.

 

OK

Note When the computer does not indicate the speed, check

 

the position of the magnet and the sensor.

 

 

Kilometer

 

Mile

 

 

 

 

 

 

 

 

 

MODE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Choose Either of The Followings.

 

 

 

 

L cm

 

 

 

• When you want to input the reading of the currently

 

 

 

 

 

 

 

 

 

used odometer, keep pressing the MODE button for

 

You can refer to the guide

 

two seconds and input the reading.

 

chart to roughly know the

 

• When you want to start the odometer from zero,

 

tire circumference.

 

 

 

 

push the START/STOP button.

 

 

 

 

 

 

 

 

 

Starting the odom- Retaining the current odometer reading

 

 

 

 

 

 

 

 

Tire size

L(cm)

 

 

eter from zero.

(the odometer starts from the reading you

 

 

 

 

 

 

 

 

14 x 1.50

102

 

 

 

inputted)

 

 

14 x 1.75

106

 

 

 

 

 

 

 

 

 

 

16 x 1.50

119

 

 

 

 

 

 

 

 

 

 

16 x 1.75

120

 

 

 

 

 

 

 

 

 

 

18 x 1.50

134

 

 

 

 

 

For two seconds.

 

 

18 x 1.75

135

 

 

 

 

MODE

 

 

20 x 1.75

152

 

 

 

 

 

 

20 x 1-3/8

162

 

 

ST/STOP

Input the current reading of odometer.

 

 

22 x 1-3/8

177

 

 

 

 

 

22 x 1-1/2

179

 

 

 

 

 

 

 

 

 

 

24 x 1

175

 

 

 

 

 

 

Increase the

 

 

24 x 3/4Tubular

178

 

 

 

 

 

 

 

 

24 x 1-1/8

179

 

 

 

 

 

 

number.

 

 

 

 

 

 

 

 

 

 

24 x 1-1/4

191

 

 

 

 

 

 

 

 

 

 

24 x 1.75

189

 

 

 

 

 

MODE

 

 

24 x 2.00

192

 

 

 

 

 

Move the

 

 

24 x 2.125

196

 

 

 

 

 

 

 

26 x 7/8

192

 

 

 

 

 

decimal point.

 

 

26 x 1(59)

191

 

 

 

 

 

 

 

 

 

 

26 x 1(65)

195

 

 

 

 

ST/STOP

 

 

26 x 1.25

195

 

 

 

 

 

 

 

 

 

 

26 x 1-1/8

190

 

 

 

 

 

 

 

 

 

 

26 x 1-3/8

207

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26 x 1-1/2

210

 

 

 

 

 

 

 

 

 

 

26 x 1.40

200

 

 

 

 

 

 

 

 

 

 

26 x 1.50

201

 

 

 

 

SET

 

 

 

 

26 x 1.75

202

 

 

 

 

 

 

 

 

26 x 1.95

205

 

 

 

 

 

 

 

 

 

 

26 x 2.00

206

 

 

 

 

 

 

 

 

 

 

26 x 2.10

207

 

 

 

 

 

 

 

 

 

 

26 x 2.125

207

 

 

Set The Tire Circumference

 

 

 

 

26 x 2.35

208

 

 

 

 

 

 

26 x 3.00

217

 

 

3 Set the tire circumference in cm.

 

 

 

 

27 x 1

215

 

 

 

 

 

 

Note You can easily set it by referring to the chart shown

 

 

27 x 1-1/8

216

 

 

 

 

27 x 1-1/4

216

 

 

right.

 

 

27 x 1-3/8

217

 

 

Setting is completed by pushing the SET button.

 

 

650 x 35A

209

 

 

 

 

650 x 38A

212

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

650 x 38B

211

 

 

 

 

 

Increase the

 

 

700 x 18C

207

 

 

 

 

 

number.

 

 

700 x 19C

208

 

 

 

 

 

 

 

700 x 20C

209

 

 

 

 

 

Max. 300 cm

 

 

 

 

 

 

 

 

 

700 x 23C

210

 

 

 

 

MODE

 

 

 

 

SET

 

 

 

700 x 25C

211

 

 

 

 

Decrease

 

 

700 x 28C

214

 

 

 

 

 

 

 

700 x 30C

217

 

 

 

 

 

the number

 

 

700 x 32C

216

 

 

 

 

 

Min. 100 cm

 

 

700C Tubular

213

 

 

 

 

ST/STOP

 

 

700 x 35C

217

 

 

 

 

 

 

700 x 38C

218

 

 

 

 

 

 

 

 

 

 

700 x 40C

220

 

 

 

Preparation Complete.

 

 

 

 

 

 

 

 

 

 

 

Tire size is usually shown

 

(the screen will show the time measurement in this state)

 

 

on the sidewall of tires.

* The auto mode is ON in this state.

Page 1
Image 1
Cateye CC-ED300 owner manual Mounted securely and the screws are not loosen, Installation of the Computer on Your Bike

CC-ED300 specifications

The Cateye CC-ED300 is a versatile cycling computer that is designed to enhance the riding experience for cyclists of all levels. With a sleek, user-friendly design, it integrates advanced technology and features that cater to both casual riders and serious athletes.

One of the standout features of the CC-ED300 is its dual sensor capability, allowing it to track both speed and cadence simultaneously. This dual functionality allows cyclists to monitor their performance more effectively, providing insights into pedaling efficiency and overall riding effectiveness. The device is equipped with an easy-to-read LCD display, which provides clear visibility of essential metrics, even in direct sunlight.

The CC-ED300 boasts multiple functions, offering data on current speed, average speed, maximum speed, trip distance, total distance, riding time, and more. These metrics enable users to set goals and track progress over time, transforming the cycling experience into a more data-driven activity. Whether you’re commuting to work or training for a race, this cycling computer serves as a reliable companion that keeps you informed.

To enhance convenience, the CC-ED300 features a wireless design, eliminating the hassle of tangled cables and allowing for easy installation on various bike frames. Its robust wireless technology ensures minimal interference, providing real-time data without dropouts. Additionally, the unit is powered by a long-lasting battery, resulting in minimal maintenance and hassle for users.

Another notable characteristic of the CC-ED300 is its ability to store personal data profiles for multiple users. This feature is ideal for families or groups of cyclists who share a bike, as it allows each rider to have tailored settings and recorded metrics.

Moreover, the Cateye CC-ED300 is built to withstand the rigors of cycling in various weather conditions. Its durable construction ensures reliability and longevity, making it suitable for both road cycling and mountain biking adventures.

In summary, the Cateye CC-ED300 is an advanced cycling computer that combines functionality with ease of use. With its dual sensor capability, extensive metrics, wireless design, and user-friendly interface, it is an indispensable tool for cyclists looking to optimize their performance and enjoy their ride to the fullest. Whether you are a beginner or a seasoned cyclist, the CC-ED300 elevates your cycling experience by providing the necessary data to push your limits and achieve your goals.