While your NexStar telescope requires little maintenance, there are a few things to remember that will ensure your telescope performs at its best.

Care and Cleaning of the Optics

Occasionally, dust and/or moisture may build up on the corrector plate of your telescope. Special care should be taken when cleaning any instrument so as not to damage the optics.

If dust has built up on the corrector plate, remove it with a brush (made of camel’s hair) or a can of pressurized air. Spray at an angle to the lens for approximately two to four seconds. Then, use an optical cleaning solution and white tissue paper to remove any remaining debris. Apply the solution to the tissue and then apply the tissue paper to the lens. Low pressure strokes should go from the center of the corrector to the outer portion. Do NOT rub in circles!

You can use a commercially made lens cleaner or mix your own. A good cleaning solution is isopropyl alcohol mixed with distilled water. The solution should be 60% isopropyl alcohol and 40% distilled water. Or, liquid dish soap diluted with water (a couple of drops per one quart of water) can be used.

Occasionally, you may experience dew build-up on the corrector plate of your telescope during an observing session. If you want to continue observing, the dew must be removed, either with a hair dryer (on low setting) or by pointing the telescope at the ground until the dew has evaporated.

If moisture condenses on the inside of the corrector, remove the accessories from the rear cell of the telescope. Place the telescope in a dust-free environment and point it down. This will remove the moisture from the telescope tube.

To minimize the need to clean your telescope, replace all lens covers once you have finished using it. Since the rear cell is NOT sealed, the cover should be placed over the opening when not in use. This will prevent contaminants from entering the optical tube.

Internal adjustments and cleaning should be done only by the Celestron repair department. If your telescope is in need of internal cleaning, please call the factory for a return authorization number and price quote.

Corrector

Plate

Collimation

Screws

Figure 7-1

The three collimation screws are located on the secondary mirror holder in the center of the corrector plate.

Collimation

The optical performance of your NexStar telescope is directly related to its collimation, that is the alignment of its optical system. Your NexStar was collimated at the factory after it was completely assembled. However, if the telescope is dropped or jarred severely during transport, it may have to be collimated. The only optical element that may need to be adjusted, or is possible, is the tilt of the secondary mirror.

To check the collimation of your telescope you will need a light source. A bright star near the zenith is ideal since there is a minimal amount of atmospheric distortion. Make sure that tracking is on so that you won’t have to manually track the star. Or, if you do not want to power up your telescope, you can use Polaris. Its position relative to the celestial pole means that it moves very little thus eliminating the need to manually track it.

Before you begin the collimation process, be sure that your telescope is in thermal equilibrium with the surroundings. Allow 45 minutes for the telescope to reach equilibrium if you move it between large temperature extremes.

40

Page 38 Page 40
Page 39
Image 39
Celestron 8i manual Care and Cleaning of the Optics, Collimation
Page 38 Page 40

8i specifications

The Celestron 8i is a highly regarded telescope that has made a significant impact in the world of amateur astronomy, renowned for its performance, advanced features, and user-friendly design. Part of Celestron's Advanced Series, the 8i model boasts an impressive 8-inch Schmidt-Cassegrain optical system, which combines the advantages of a large aperture with a compact design. This allows enthusiasts to explore celestial objects with greater clarity, providing bright, sharp images of planets, star clusters, and nebulae.

One of the standout features of the Celestron 8i is its Fast Star capability, which allows for rapid imaging of celestial objects. Coupled with its advanced StarBright XLT coatings, this system enhances light transmission and increases contrast, resulting in a more vivid and detailed observation experience. This combination makes it an ideal choice for both novice and experienced astronomers who seek high-quality visuals of deep-sky objects.

The telescope's computer-controlled GoTo mount simplifies the process of locating and tracking celestial objects. With the push of a button, users can easily access a database containing over 40,000 astronomical objects, allowing for an effortless stargazing experience. The Celestron 8i also features an intuitive hand controller that enables users to customize their observations and seamlessly navigate the night sky.

The Celestron 8i is designed for portability, despite its robust optical performance. Weighing in at around 45 pounds, it is relatively easy to transport to different observing locations. The telescope's sturdy construction ensures stability while providing ease of setup, facilitating a hassle-free stargazing experience.

In terms of accessories, the 8i comes equipped with a 25mm eyepiece, offering a moderate magnification that is perfect for a variety of targets. Additionally, users can expand their observing capabilities with optional eyepieces, filters, and focal reducers, catering to both visual and astrophotography pursuits.

Overall, the Celestron 8i stands out as a versatile and powerful telescope that meets the needs of amateur astronomers at various skill levels. With its advanced features, superior optics, and impressive usability, the 8i offers a unique and rewarding experience under the night sky. Whether for planetary observation or deep-sky exploration, the Celestron 8i remains a top choice for astronomy enthusiasts.
Top Page Image Contents