CFM UVHK36MN, UVHK29MN, UVHK23MP, UVHK31MP manual Clockwise, Counterclockwise

Fig. 6

For Your Safety, Read Before Lighting

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE OPERATION smell all around the appliance area for gas. Be sure to smell

next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL

GAS:

• Do not try to light any appliance. Piezo

•Do not touch any electrical switch;

do not use any telephone in your building.

•Immediately call your gas supplier from a neighbor’s tele- phone.

•Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire depart- ment.

C. Use only your hand to push in		Clockwise
or turn the gas control knob.	Fig. 7
Never use tools. If the knob		3
will not push in or turn by hand,
	2	4
don’t try to repair it. Call a
qualified service technician.
Force or attempted repair may	1/IGN
cause a fire or an explosion.
D. Do not use this appliance if
any part of it has been under	Off
water. Immediately call a
qualified service technician to
inspect the appliance and to

replace any part of the control system or gas control which has been under water.

Lighting Instructions

1.STOP! Read the safety information above before proceed- ing.

2.Refer to Figure 7. To turn off the gas supply, depress the

knob slightly and turn clockwise to the OFF position.

3.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Fol- low “B” in the safety information above. If you don’t smell gas, go to the next step.

4. Refer to Figure 8. Locate the pilot. It is at the right of the front main burner next to the control knob.

5. Refer to Figure 9. Fig. 8

Push in the control knob

and turn counterclockwise to the 1/IGN position. Hold the control knob in for a few seconds.

6.While still holding in the control knob, press the ignitor push- button several times. This will cause a spark at the pilot which will ignite the pilot gas.

7.Hold the control knob for 20 seconds to prevent the flame failure detector from shutting off the gas while its probe is warming up.

8. Release the control knob.

•If the knob does not pop up when released, stop and im- mediately call your service

technician.		Counterclockwise
• If the pilot will not stay lit after		Fig. 9
several tries, turn the gas
		3
control knob to OFF and call			4
		2
your service technician or gas
supplier.
9. When the pilot remains lit, turn		1/IGN
the control knob counterclock-
wise	to the setting you	Off
prefer.

10.Refer to the table on Page 5 for setting positions.

11.This appliance is fitted with a transient pilot burner for the sole purpose of safe, momentary ignition of the main burner in conjunction with the piezo ignitor. When in operation with the main burner, it contributes to the base heat release and is turned off by turning the control knob to the OFF position.

12.The control knob should not be left at the ignition setting after the pilot has been ignited.

To Turn OFF Gas to Appliance

Depress the control knob slightly and turn it clockwise to the OFF position. Refer to Figure 7.

Match Lighting

If the pilot cannot be ignited with the piezo, it can be manually lit with the use of a match and lighter rod.

1.Place the match in the holder and light. With the right hand, depress and turn the control knob counterclock-

wise (Fig. 9) to the “IGN” position. Hold in for 20 seconds.

2.Take the lighter rod and lighted match and ignite the pilot

.(Fig. 8)

3.Continue to hold the control knob for an additional 20 sec- onds to ensure pilot is maintained.

4.Proceed with Step 8 in Lighting Instructions.

20008056 13