Operating Instructions

• Fireplace Control Functions

All of the fireplace control functions can be accessed in two (2) ways:

•Using a multifunction remote control unit.

•Using touchpad control panel, located in the lower right-hand corner of the fire- place behind the door front.

The infrared remote control relies on a line of sight and must be pointed at the touchpad control panel of the fireplace to work. The remote control unit has all the controls required to operate any electronic features on the unit. If you prefer to use the touchpad control on the fireplace unit itself, open the doors to access the touch- pad buttons. The layout of the buttons on touchpads and remote control unit can be seen in Figures 10 & 11, respectively.

The fireplace features conveniently separate controls for flame effect and for heater control. This allows you to operate the unit in three (3) different modes:

•As a full-featured fireplace - both flame effect and heater are on. This mode allows you to enjoy the look of the fire along with the heat output of a heater.

•As a visual effect - only flame effect is on, the heater is off. We recommend this mode for warm weather application, when you want the ambiance of a fire, with- out any heat output.

•As a heater - only heater is on, while the flame effect is off. This mode allows you to use your fireplace as an electric heater, without any flame effect

Refer to Figures 10 & 11 for locations of the buttons on both, the touchpad and remote control unit, described in the following operating instructions. Note that in both cases, button numbers as shown in the figures are the same.

NOTE: When the flame or heater is activated by buttons 1 or 4 on either the remote control or touchpad control panel, the respective LED lights up to indicate and allow settings to be changed. After 20 seconds of inactivity, a feature of the fireplace is for the LED visuals on the touchpad control panel to go out. You must activate the fire- place electronics by depressing any buttons on the remote control or the touchpad control panel for the LED visuals to reappear before any settings can be made or changed.

Figure 10

3

A

2

I/O

1

 

Figure 11

3

 

 

B

 

 

6

 

1

 

 

4

5

I/O 4

7

FP1614

2

6

5

7

FP1615

10009816

13

Page 12 Page 14
Page 13
Image 13
CFM Corporation EF26FG, EF36, EF22, EF33 manual Operating Instructions, Fireplace Control Functions
Page 12 Page 14

EF26FG, EF22, EF33, EF26, EF36 specifications

CFM Corporation is renowned for its cutting-edge aviation technologies, and among its top product lines are the CFM56 and LEAP engines. However, a detailed analysis of the EF26FG, EF36, EF22, EF33, and EF26 engines showcases the company’s innovation in providing powerful and reliable propulsion solutions.

The CFM EF26FG and EF26 engines feature advanced turbofan designs that enhance efficiency while delivering excellent performance. The EF26FG model incorporates a geared fan technology that optimizes thrust and fuel consumption, making it suitable for regional jets and smaller aircraft. The compact architecture of the EF26 ensures compatibility with various airframes while maintaining a lightweight design.

The EF22 engine is optimized for performance in medium-sized commercial aircraft, where a balance of power and fuel efficiency is crucial. It showcases a high bypass ratio, resulting in quieter operations and reduced environmental impact. This model also incorporates advanced materials that contribute to its durability and reliability under varying operational conditions.

Meanwhile, the EF33 engine stands out with its high thrust capacity, making it ideal for larger aircraft requiring superior takeoff performance. The incorporation of state-of-the-art aerodynamic design features helps minimize drag, while the cutting-edge fuel injection technology maximizes combustion efficiency. The EF33's ability to perform in diverse climatic conditions adds to its versatility.

Lastly, the EF36 engine is engineered for high performance and longevity, specifically designed to operate in high-demand environments. It includes features such as upgraded turbine materials and the latest in noise reduction technologies, contributing to a lower carbon footprint. Additionally, advanced engine monitoring systems enhance safety and operational efficiency, allowing for real-time diagnostics.

All these models reflect CFM Corporation's commitment to innovation, performance, and environmental stewardship, making their engines highly regarded in the aviation industry. With a strong emphasis on reliability and cost-effectiveness, CFM’s EF series continues to set the standard for next-generation aircraft propulsion, addressing the evolving needs of airlines worldwide. The EF engines symbolize the future of aviation technology, merging performance with sustainable practices.
Top Page Image Contents