Main
Start by reviewing these important safety alert symbols
serious injuries or death
Mechanical Electrical
Read the instructions carefully.
You'll Need Tools
WARNING CAUTION
Ropes left on a garage door could cause someone to become entangled and killed.
Sectional Door Installation
One-Piece Door Installation without Track
FINISHED CEILING Support bracket & fastening hardware is required. See page 13.
One-Piece Door with Track
Carton Inventory
ASSEMBLY STEP 1
Attach the T-Rail To the Opener
Figure C
Figure A
USE ONLY THESE SCREWS!
IMPORTANT INST ALLATION INSTRUCTIONS To reduce the risk of severe injury or death to persons:
An improperly balanced door may not reverse and could result in severe injury or death.
Ropes connected to a garage door can cause entanglement and death.
Proceed to Step 2, page 10.
SECTIONAL Doors and ONE-PIECE Door With Track
Installation Section: Pages 8 23
Installation Step 1
Determine Header Bracket Location
The door might not reverse when required, and could cause serious injury or death.
Proceed to Step 2, page 10.
ONE-PIECE Door Without Track
Read the Safety Instructions on page 8. They also apply to doors without tracks.
Fasten the Header Bracket to the Wall
Fasten the Header Bracket to the Ceiling
Installation Step 2
Install the Header Bracket
,
Liftmaster Synchro Drive Tee Rail to Header Bracket 5/16/92
Installation Step 3
Attach the T-rail to the Header Bracket
Installation Step 4
Position the Opener
SECTIONAL Door & ONE-PIECE Door with Track
ONE-PIECE Door without Track
You will need help at this point if the ladder is not tall enough.
Installation Step 5
Hang the Opener
each
The opener could fall and injure someone if it is not properly secured.
Figure 1
Installation Step 6
Install the Door Control Panel
Do not overtighten.
Hardware Shown Actual Size
Installation Step 7
Install the Lights and the Lenses
Installation Step 8
Attach the Manual Release Rope and Handle
The rope knot could become untied and you could fall.
Installation Step 9
and
NOT
To prevent electrocution or fire,
Electrical Requirements
The ProtectorSystem
must
Installation Step 10
Install the Safety Reversing Sensor
Garage door track installation (preferred):
Wall installation:
Floor installation:
Figure 6
Figure 5
glows steadily
sending eye
glows steadily,
Installation Step 11
Fasten Door Bracket
Figure 2
Note the correct UP placement as stamped inside the bracket.
SECTIONAL Door Installation Procedure
All ONE-PIECE Door Installation Procedure
Installation Step 12
Connect Door Arm to Trolley
Hole Alignment Alternative
Figure 3
above
Can/DoorArmToTrolley 1 pc
All ONE-PIECE Doors
Adjustment Procedures for One-Piece Doors
Adjustment Step 1
Adjust the UP and DOWN Limits
down
reverses
up
Adjustment Step 2
Adjust the Force
reverses
at least
up
Adjustment Step 4
Test the Safety Reverse System
Important safety check:
Adjustment Step 3
Test the Protector System
IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of severe injury or death to persons:
Limit and force adjustment controls
Maintenance Schedule
must
MUST
Operation of Your Opener
To turn off:
To activate:
Automatic Light Feature,
when the door is fully closed.
Receiver and Remote Control Programming
SECURITY
NOTE: Open/Close/Stop operation counts as 1 function.
flash once. 3.
press and hold a remote push button.
Having a Problem?
Situation Probable Cause & Solution
Having a Problem?
(continued)
Situation Probable Cause & Solution
Page
Repair Parts
Accessories Available For Your Opener
Required
To Add the Keyless Entry
With the door closed,
hold
Index
2000, The Chamberlain Group, Inc. 114A2478 All Rights Reserved Printed in Mexico
LIFT-MASTER SERVICE IS ON CALL
1-800-654-4736
HOW TO ORDER REPAIR PARTS
1-800-654-4736
LIFT-MASTER GARAGE DOOR OPENER FIVE-YEAR LIMITED WARRANTY