B) To operate one door using
all three buttons on the
hand-held remote:
You may program the remote to
open the door with the large button, close it with the
middle button, and stop the door’s movement with
the third button.
NOTE: If remote is already programmed, you must
first erase all codes. See Programming.
1.With the door closed, press and hold the large
remote push button.
2.Press and hold the Lock button on the door
control.
3.Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
To Open the Door Manually
The door should be fully
closed if possible. Pull down
on the emergency release
handle and lift the door
manually. To reconnect the
door to the opener, press the
door control push bar.
The lockout feature prevents
the trolley from reconnecting
automatically, Pull the
emergency release handle
down and back (toward the
opener). The door can then
be raised and lowered
manually as often as
necessary. To disengage the
lockout feature, pull the
handle straight down. The
trolley will reconnect on the next UP or DOWN
operation.
• To prevent possible SERIOUS INJURYor DEATH from
a falling garage door:
– If possible, use emergency release handle to
disengage trolley ONLYwhen garage door is
CLOSED. Weak or broken springs or unbalanced
door could result in an open door falling rapidly
and/or unexpectedly.
– NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope
knot becomes untied, you could fall.
28
Using the Wall-Mounted Door Control
THE MULTI-FUNCTION DOOR CONTROL
Press the push bar to open or
close the door. Press again to
reverse the door during the
closing cycle or to stop the door
while it's opening.
Light feature
Press the Light button to turn the opener light on or
off. It will not control the opener lights when the door
is in motion. If you turn it on and then activate the
opener, the light will remain on for 4-1/2 minutes.
Press again to turn it off sooner. The 4-1/2 minute
interval can be changed to 1-1/2, 2-1/2, or 3-1/2
minutes as follows: Press and hold the Lock button
until the light blinks (about 10 seconds). Asingle blink
indicates that the timer is reset to 1-1/2 minutes.
Repeat the procedure and the light will blink twice,
resetting the timer to 2-1/2 minutes. Repeat again for
a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from hand-
held remote controls. However, the door will open
and close from the Door Control, the Outside Keylock
and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2
seconds. The push bar light will flash as long as the
Lock feature is on.
To turn off, press and hold the Lock button again for
2 seconds.The push bar light will stop flashing. The
Lock feature will also turn off whenever the “Smart”
(learn) button on the motor unit panel is activated.
Additional features when used
with the
3-Channel hand-held remote
A) To control the opener lights:
In addition to operating the door, you may program
the remote to operate the lights.
1.With the door closed, press and hold a small
remote button that you want to control the light.
2.Press and hold the Light button on the Multi-
Function door control.
3.While holding the Light button, press and hold the
Lock button on the door control.
4.After the opener lights flash, release all buttons.
WARNING
CAUTION WARNING
WARNING
Open
Close
Stop
LOCK
LIGHT
Push
Bar
Lock
Button
Light
Button
Trolley
Release
Arm
NOTICE
Emergency
Release
Handle
(Pull Down)
Trolley
Release
Arm
NOTICE
Emergency
Release Handle
(Pull Down & Back
Towards Opener)
LOCKOUT POSITION
MANUALDISCONNECT
POSITION